|
|
|
题名
|
作者
|
年代
|
出处
|
被引量
|
| 1 | Formation Mechanism and Controlling Factors of Natural Gas Reservoirs of the Jialingjiang Formation in the East Sichuan Basin显示文摘The Lower Triassic Jialingjiang Formation reservoirs are distributed widely in the East Sichuan Basin,which are composed mainly of fractured reservoirs.However,natural gas with high concentration of H_2S,ranging from 4% to 7%,was discovered in the Woionghe Gas pool consisting primarily of porous reservoirs,while the other over 20 fractured gas reservoirs have comparatively low,tiny and even no H_2S within natural gases.Researches have proved the H_2S of the above reservoirs are all from the TSR origin.Most of the Jialingjiang Formation natural gases are mainly generated from Lower Permian carbonate rocks,the Wolonghe gas pool's natural gases are from the Upper Permian Longtan Formation,and the natural gases of the Huangcaoxia and Fuchengzhai gas pools are all from Lower Silurian mudstone.The formation of H_2S is controlled by the characteristics and temperature of reservoirs,and is not necessarily related with gas sources.The Jialingjiang Formation in East Sichuan is buried deeply and its reservoir temperature has ever attained the condition of the TSR reaction.Due to poor reservoir potential,most of the gas pools do not have enough room for hydrocarbon reaction except for the Wolonghe gas pool,and thus natural gases with high H_2S concentration are difficult to be generated abundantly.The south part of East Sichuan did not generate natural gases with high H_2S concentration because the reservoir was buried relatively shallow,and did not suffer high temperature.Hence,while predicting the distribution of H_2S,the characteristics and temperature of reservoirs are the necessary factors to be considerd besides the existence of anhydrite. | ZHU Guangyou ZHANG Shuichang LIANG Yingbo ZHOU Guoyuan WANG Zhengjun | 2007 | Acta Geologica Sinica(English Edition)2007，81，5： | 16 |
| 2 | Dry Friction and Wear Characteristics of Impregnated Graphite in a Corrosive Environment显示文摘Tribological properties of impregnated graphite are greatly influenced by preparation technology and working conditions and it’s highly susceptible to corrosion environmental impacts,but the experimental research about it are few.In this paper,three kinds of impregnated graphite samples are prepared with different degree of graphitization,the tribological properties of these samples in the dry friction environment and in a corrosive environment are analyzed and contrasted.The tribo-test results show that the friction coefficient of samples is reduced and the amount of wear of samples increase when the graphitization degree of samples increases in dry friction condition.While in a corrosive environment(samples are soaked N2O4),the friction coefficient and amount of wear are changed little if the graphitization degree of samples are low.If the degree of graphitization increase,the friction coefficient and amount of wear of samples increase too,the amount of wear is 2 to 3 times as the samples tested in the non-corrosive environment under pv value of 30MPa?m/s.The impregnated graphite,which friction coefficient is stable and graphitization degree is in mid level,such#2,is more appropriate to have a work in the corrosion conditions.In this paper,preparation and tribological properties especially in corrosive environment of the impregnated graphite is studied,the research conclusion can provide an experimental and theoretical basis for the selection and process improvement of graphite materials,and also provide some important design parameters for contact seal works in a corrosive environment. | JIA Qian YUAN Xiaoyang ZHANG Guoyuan DONG Guangneng ZHAO Weigang | 2014 | Chinese Journal of Mechanical Engineering2014，27，5： | 15 |
| 3 | MTBAC: A Mutual Trust Based Access Control Model in Cloud Computing显示文摘As a new computing mode,cloud computing can provide users with virtualized and scalable web services,which faced with serious security challenges,however.Access control is one of the most important measures to ensure the security of cloud computing.But applying traditional access control model into the Cloud directly could not solve the uncertainty and vulnerability caused by the open conditions of cloud computing.In cloud computing environment,only when the security and reliability of both interaction parties are ensured,data security can be effectively guaranteed during interactions between users and the Cloud.Therefore,building a mutual trust relationship between users and cloud platform is the key to implement new kinds of access control method in cloud computing environment.Combining with Trust Management(TM),a mutual trust based access control(MTBAC) model is proposed in this paper.MTBAC model take both user's behavior trust and cloud services node's credibility into consideration.Trust relationships between users and cloud service nodes are established by mutual trust mechanism.Security problems of access control are solved by implementing MTBAC model into cloud computing environment.Simulation experiments show that MTBAC model can guarantee the interaction between users and cloud service nodes. | LIN Guoyuan WANG Danru BIE Yuyu LEI Min | 2014 | China Communications2014，11，4： | 12 |
| 4 | First observation of thermospheric neutral wind at Chinese Yellow River Station in Ny-lesund, Svalbard显示文摘A compact and cost-effective all-sky Fabry-Perot interferometer, which is produced by Wuhan University and used for the observation of the thermospheric neutral wind, was installed at Chinese Yellow River Station in Nylesund, Svalbard in November 2010, and continuously operated in last two winter seasons. The 92-day all-sky interference data acquired from November 1, 2011 to February 26, 2012 were collected to get the velocity of thermospheric neutral wind, which was calculated from the Doppler shift caused by the movement of oxygen atom at the different layers. The database was divided into two periods: (1) The OI 557.7 nm emission was observed from November 1, 2011 to January 12, 2012. Observations showed that the velocity of horizontal wind is normally less than ~40 m/s on the quiet condition, and exceeded 100 m/s on the disturbed condition; and (2) the OI 630.0 nm emission was observed from January 13, 2012 to February 26, 2012. Observations showed that the velocity of horizontal wind is normally less than ~200 m/s, and enhanced to over 300 m/s on strong magnetic activities. It shows that the velocities of meridional and zonal wind are more consistent with the velocities calculated from the model HWM07 at the higher layer, especially for the zonal direction at nightside auroral regions. Ion drag and Joule heating were the two important processes considered in the analysis of the relationship between the wind pattern and aurora, suggesting that wind speed would be increased and accelerated in the direction perpendicular to the aurora arc when the aurora activity becomes strong. | ZHANG Hong AI Yong ZHANG YanGe HU GuoYuan | 2013 | Chinese Science Bulletin2013，58，11： | 10 |
| 5 | Additively manufactured biodegradable porous magnesium implants for elimination of implant-related infections:An in vitro and in vivo study显示文摘Magnesium(Mg)alloys that have both antibacterial and osteogenic properties are suitable candidates for orthopedic implants.However,the fabrication of ideal Mg implants suitable for bone repair remains challenging because it requires implants with interconnected pore structures and personalized geometric shapes.In this study,we fabricated a porous 3D-printed Mg-Nd-Zn-Zr(denoted as JDBM)implant with suitable mechanical properties using selective laser melting technology.The 3D-printed JDBM implant exhibited cytocompatibility in MC3T3-E1 and RAW267.4 cells and excellent osteoinductivity in vitro.Furthermore,the implant demonstrated excellent antibacterial ratios of 90.0% and 92.1% for methicillin-resistant S.aureus(MRSA)and Escherichia coli,respectively.The 3D-printed JDBM implant prevented MRSA-induced implant-related infection in a rabbit model and showed good in vivo biocompatibility based on the results of histological evaluation,blood tests,and Mg2+deposition detection.In addition,enhanced inflammatory response and TNF-α secretion were observed at the bone-implant interface of the 3D-printed JDBM implants during the early implantation stage.The high Mg^(2+)environment produced by the degradation of 3D-printed JDBM implants could promote M1 phenotype of macrophages(Tnf,iNOS,Ccl3,Ccl4,Ccl5,Cxcl10,and Cxcl2),and enhance the phagocytic ability of macrophages.The enhanced immunoregulatory effect generated by relatively fast Mg^(2+)release and implant degradation during the early implantation stage is a potential antibacterial mechanism of Mg-based implant.Our findings indicate that 3D-printed porous JDBM implants,having both antibacterial property and osteoinductivity,hold potential for future orthopedic applications. | Kai Xie Nanqing Wang Yu Guo Shuang Zhao Jia Tan Lei Wang Guoyuan Li Junxiang Wu Yangzi Yang Wenyu Xu Juan Chen Wenbo Jiang Penghuai Fu Yongqiang Hao | 2022 | Bioactive Materials2022，7，2： | 8 |
| 6 | Investigation into the energy consumption of a data center with a thermosyphon heat exchanger显示文摘A data center test model was used to analyze the energy dissipation characteristics and energy consumption of a data center.The results indicate that adequate heat dissipation from a data center cannot be achieved only from heat dissipation through the building envelope during Beijing winter conditions.This is because heat dissipation through the building envelope covers about 19.5% of the total data center heat load.The average energy consumption for an air conditioner is 4 to 5 kW over a 24-h period.The temperature difference between the indoor and outdoor air for the data center with a thermosyphon heat exchanger is less than 20°C.The energy consumption of the thermosyphon heat exchanger is only 41% of that of an air conditioner.The annual energy consumption can be reduced by 35.4% with a thermosyphon system.In addition,the effect of the outdoor temperature on the en-ergy consumption of an air conditioner is greater than the indoor room temperature.The energy consumption of an air conditioner system increases by 5%to 6%for every 1°C rise in the outdoor temperature. | ZHOU Feng TIAN Xin MA GuoYuan | 2011 | Chinese Science Bulletin2011，56，20： | 8 |
| 7 | An Audio Zero-Watermark Scheme Based on Energy Comparing显示文摘Zero-watermark technique,embedding watermark without modifying carriers,has been broadly applied for copyright protection of images.However,there is little research on audio zerowatermark.This paper proposes an audio zero-watermark scheme based on energy relationship between adjacent audio sections.Taking use of discrete wavelet transformation(DWT),it gets power approximations,or energies,of audio segments.Then,it extracts the audio profile,i.e.the zero-watermark,according to the relative size of energies of consecutive fragments.The experimental results demonstrate that the proposed scheme is robust against general malicious attacks including noise addition,resampling,low-pass filtering,etc.,and this approach effectively solves the contradiction between inaudibility and robustness. | YANG Yu LEI Min CHENG Mingzhi LIU Bohuai LIN Guoyuan XIAO Da | 2014 | China Communications2014，11，7： | 7 |
| 8 | Friction and wear behavior of different seal materials under water-lubricated conditions显示文摘The shaft mechanical face seal in a high-speed turbopump of a liquid rocket engine often operates under extremely harsh conditions.For example,a low-temperature and low-viscosity fluid(such as liquid oxygen or liquid hydrogen)is used as a lubricant.The performance of the seal rings,especially the friction and wear behavior,directly determines whether the seal functions normal.In this study,the friction and wear behavior of several ring materials are tested using a pin-on-disk tribo-tester,and the wear morphology of the ring is investigated.The friction coefficients(COFs)and mass-wear rates under dry-friction and water-lubricated conditions,which are used to simulate low-viscosity conditions,are obtained.The results show that at a pressure-velocity(PV)value of 2.4 MPa-(m/s),the COF between the copper graphite(stator)and copper-chrome alloy disk(rotor)is low(with a value of 0.18)under the dry-friction conditions,and the 5-min wear mass of the copper graphite is approximately 2 mg.Under the water-lubricated conditions,compared with other materials(such as copper-chrome alloy,S07 steel,alumina ceramic coating,and nickel-based calcium fluoride),the S07 steel with a diamond-like carbon film is preferred for use in a high-speed turbopump under extreme conditions.The results of this study can provide theoretical and experimental guidance in the design of mechanical face seals in liquid rocket engines. | Weigang ZHAO Guoyuan ZHANG Guangneng DONG | 2021 | Friction2021，9，4： | 5 |
| 9 | Contributions of phosphatase and microbial activity to internal phosphorus loading and their relation to lake eutrophication显示文摘Phosphatase may accelerate the process of lake eutrophication through improving phosphorus bioavailability. This mechanism was studied in three Chinese eutrophic shallow lakes (Lake Taihu, Lake Longyang and Lake Lianhua). Phosphatase activity was related to the concentration of soluble reactive phosphorus (SRP) and chlorophyll a. Stability of dissolved phosphatase in reverse micelles may be attributed to molecular size, conformation and active residues of the enzyme.At the site with Microcystis bloomed in Lake Taihu, dissolved phosphatase activity was higher and more stable in micelles, SRP concentrations were lower in interstitial water, the contents of different forms of phosphorus and the amounts of aerobic bacteria were lower while respiration efficiency was higher in sediments. Phosphobacteria, both inorganic and organic and other microorganisms were abundant in surface water but rare in sediments. Therefore, internal phosphorus may substantially flux into water column by enzymatic hydrolysis and anaerobic release, together with mobility of bacteria,thereby initiating the bloom. In short, biological mechanism may act in concert with physical and chemical factors to drive the internal phosphorus release and accelerate lake eutrophication. | SONG Chunlei, CAO Xiuyun, LI Jianqiu, LI Qingman, CHEN Guoyuan & ZHOU Yiyong Institute of Hydrobiology, Chinese Academy of Sciences, Wuhan 430072, China Graduate School of the Chinese Academy of Sciences, Beijing 100039, China | 2006 | Science China Earth Sciences2006，49，z1： | 5 |
| 10 | On-ramp merging strategy for connected and automated vehicles based on complete information static game显示文摘Improper handling of vehicle on-ramp merging may hinder traffic flow and contribute to lower fuel economy,while also increasing the risk of collisions.Cooperative control for connected and automated vehicles(CAVs)has the potential to significantly reduce negative environmental impact while also improve driving safety and traffic efficiency.Therefore,in this paper,we focus on the scenario of CAVs on-ramp merging and propose a centralized control method.Merging sequence(MS)allocation and motion planning are two key issues in this process.To deal with these problems,we first propose an MS allocation method based on a complete information static game whereby the mixed-strategy Nash equilibrium is calculated for an individual vehicle to select its strategy.The on-ramp merging problem is then formulated as a bi-objective(total fuel consumption and total travel time)optimization problem,to which optimal control based on Pontryagin's minimum principle(PMP)is applied to solve the motion planning issue.To determine the proper parameters in the bi-objective optimization problem,a varying-scale grid search method is proposed to explore possible solutions at different scales.In this method,an improved quicksort algorithm is designed to search for the Pareto front,and the(approximately)unbiased Pareto solution for the bi-objective optimization problem is finally determined as the optimal solution.The proposed on-ramp merging strategy is validated via numerical simulation,and comparison with other strategies demonstrates its effectiveness in terms of fuel economy and traffic efficiency. | Haigen Min Yukun Fang Xia Wu Guoyuan Wu Xiangmo Zhao | 2021 | Journal of Traffic and Transportation Engineering(English Edition)2021，8，4： | 5 |
| 11 | Influence of Range Gate Width on Detection Probability and Ranging Accuracy of Single Photon Laser Altimetry Satellite显示文摘The influence of the single photon laser altimeter range-gate width on the detection probability and ranging accuracy is discussed and analyzed,according to the LiDAR equation,single photon detection equation and the Monte Carlo method to simulate the experiment.The simulated results show that the probability of detection is not affected by the range gate,while the probability of false alarm is relative to the gate width.When the gate width is 100 ns,the ranging accuracy can accord with the requirements of satellite laser altimeter.But when the range gate width exceeds 400 ns,ranging accuracy will decline sharply.The noise ratio will be more as long as the range gate to get larger,so the refined filtering algorithm during the data processing is important to extract the useful photons effectively.In order to ensure repeated observation of the same point for 25 times,we deduce the quantitative relation between the footprint size,footprint,and frequency repetition according to the parameters of ICESat-2.The related conclusions can provide some references for the design and the development of the domestic single photon laser altimetry satellite. | Guoyuan LI Fanghong YE Xinming TANG Dongping XIE Jiapeng HUANG Genhua HUANG | 2020 | Journal of Geodesy and Geoinformation Science2020，3，2： | 4 |
| 12 | Analysis and Design of Asymmetric Oscillation for Caterpillar-Like Locomotion显示文摘 | Guoyuan Li Wei Li Jianwei Zhang Houxiang Zhang | 2015 | Journal of Bionic Engineering2015，12，2： | 4 |
| 13 | Air-source heat pump coupled with economized vapor injection scroll compressor and ejector:Design and experimental research显示文摘Ejector can utilize high pressure energy from liquid mechanism,it can be used in heat pump system coupled with economized vapor injection(EVI)scroll compressor.When running under low temperature conditions,the performance of the EVI system with ejector can be improved further.In this paper,the design method of the heat pump system with ejector is presented,and the process for designing the heat pump with ejector(EVIe)was summarized.One prototype heat pump was designed under the condition of the evaporation temperature of -20oC,and an experimental setup was established to test the prototype.The measured results demonstrated that the heating EER(energy efficiency ratio)of the EVIe could reach about 4%higher than that of the system without the ejector when the heating capacity remained nearly constant.The design method is helpful to development of a heat pump system coupled with scroll compressor and ejector. | XU ShuXue&MA GuoYuan Beijing University of Technology,Beijing 100124,China | 2010 | Science China(Technological Sciences)2010，53，3： | 4 |
| 14 | Performance study on three-stage power system of compressed air vehicle based on single-screw expander显示文摘A new compressed-air engine system based on three-stage single screw expander was proposed to improve the performance of power system.Three different structure styles were presented,and the studies on the power performance and the distribution of expansion ratios between stages were carried out by programming and mathematical modeling of each style.Research results indicated that the best matches of expansion ratios with equal heat temperature for the air tank of pressure 30 MPa were seven-five-three for'first-stage heating'style,eight-five-three for'two-stage heating'style and five-five-four for'three-stage heating'style,respectively.Results also showed that heating up inlet air or increasing the expander efficiency might improve the power performance.The output power of the'two-stage heating'style is far higher than that of'first-stage heating'style and is a little lower than that of'three-stage heating'style.The new system showed good structure and power performances. | HE Wei,WU YuTing ,MA ChongFang&MA GuoYuan Key Laboratory of Enhanced Heat Transfer and Energy Conservation,Ministry of Education,and Key Laboratory of Heat Transfer and Energy Conversion,Beijing Municipality,College of Environmental and Energy Engineering,Beijing University of Technology,Beijing 100124,China | 2010 | Science China(Technological Sciences)2010，53，8： | 3 |
| 15 | Design of artificial nucleases and studies of their interaction with DNA显示文摘The design of artificial nucleases and nuclease mimics has attracted extensive attention and made great progress due to their significant scientific meanings and potential application in the field of gene medicine and molecular biology. This paper reviews recent progress in the investigation of artificial nuclease,including 'bifunctional cooperative catalysis','dinuclear synergistic catalysis','metal-free catalysis' ,and especially,the studies of aza-crown ethers as artificial nucleases and their interaction with DNA. | ZHANG JingJing SHAO Ying WEI Li LI Ying SHENG Xin LIU Fang LU GuoYuan | 2009 | Science China Chemistry2009，52，4： | 3 |
| 16 | Genome sequencing and phylogenetic analysis of allotetraploid Salix matsudana Koidz显示文摘Polyploidy is a common phenomenon among willow species.In this study,genome sequencing was conducted for Salix matsudana Koidz(also named Chinese willow),an important greening and arbor tree species,and the genome of this species was compared with those of four other tree species in Salicaceae.The total genome sequence of S.matsudana was 655.72 Mb in size,with repeated sequences accounting for 45.97%of the total length.In total,531.43 Mb of the genome sequence could be mapped onto 38 chromosomes using the published genetic map as a reference.The genome of S.matsudana could be divided into two groups,the A and B genomes,through homology analysis with the genome of Populus trichocarpa,and the A and B genomes contained 23,985 and 25,107 genes,respectively.4DTv combined transposon analysis predicted that allotetraploidy in S.matsudana appeared~4 million years ago.The results from this study will help reveal the evolutionary history of S.matsudana and lay a genetic basis for its breeding. | Jian Zhang Huwei Yuan Yujuan Li Yanhong Chen Guoyuan Liu Meixia Ye Chunmei Yu Bolin Lian Fei Zhong Yuna Jiang Jichen Xu | 2020 | Horticulture Research2020，7，1： | 3 |
| 17 | Bicontinuous porous membranes with micro-nano composite structure using a facile atomization-assisted nonsolvent induced phase separation method显示文摘The micro-nano composite structure can endow separation membranes with special surface properties,but it often has the problems of inefficient preparation process and poor structural stability.In this work,a novel atomization-assisted nonsolvent induced phase separation method,which is also highly efficient and very simple,has been developed.By using this method,a bicontinuous porous microfiltration membrane with robust micro-nano composite structure was obtained via commercially available polymers of polyacrylonitrile and polyvinylpyrrolidone.The formation mechanism of the micro-nano composite structure was proposed.The microphase separation of polyacrylonitrile and polyvinylpyrrolidone components during the atomization pretreatment process and the hydrogen bonding between polyacrylonitrile and polyvinylpyrrolidone molecules should have resulted in the nano-protrusions on the membrane skeleton.The membrane exhibits superhydrophilicity in air and superoleophobicity underwater.The membrane can separate both surfactant-free and surfactant-stabilized oil-in-water emulsions with high separation efficiency and permeation flux.With excellent antifouling property and robust microstructure,the membrane can easily be recycled for long-term separation.Furthermore,the scale-up verification from laboratory preparation to continuous production has been achieved.The simple,efficient,cost-effective preparation method and excellent membrane properties indicate the great potential of the developed membranes in practical applications. | Jing Wang Guoyuan Pan Yu Li Yang Zhang Hongwei Shi Xuanbo Liu Hao Yu Muhua Zhao Yiqun Liu Changjiang Wu | 2022 | Frontiers of Chemical Science and Engineering2022，16，8： | 2 |
| 18 | First scanning Fabry–Perot interferometer developed in China显示文摘A scanning Fabry–Perot interferometer(SFPI)was first developed and deployed at the Langfang near Space Environment Field Scientific Observation Station(39.38°N,116.65°E)of the National Space Science Center,CAS.The instrument is designed to measure the mesospheric and thermospheric wind velocities using the atomic oxygen 557.7-nm and 630.0-nm emissions.Data from February 28 to March 3and February 28 to March 15 in 2011 were chosen for case study and mean value study,respectively.The errors of the meridional and zonal winds are 6.5 and 7.5 m/s at 557.7-nm and at 630.0-nm,they are 7.1 and 6.6 m/s,respectively.During the whole experiment,the instrument has performed in good condition and provided high-quality data.The mean neutral wind data were consistent with that predicted by HWM07.Good agreement has been found in between the SFPI and a neighbor Meridian Project Fabry–Perot interferometer(MP FPI),with a corresponding coefficient(r2)larger than 80%.In general,the scanning FPI meets the design goal,and it is a useful ground-based instrument for measuring mesospheric and thermospheric winds at middle latitudes and is able to provide high-quality data for future scientific studies. | Guoyuan Hu Yong Ai Yange Zhang Hong Zhang Jue Liu | 2014 | Chinese Science Bulletin2014，59，5： | 2 |
| 19 | EXPERIMENTAL INVESTIGATION ON GENERATION MECHANISM OF EXPLOSIVE STRESS WAVES显示文摘1INTRODUCTIONExplosivestresswavesarequiteimportantinrockfragmentationproces.Manyscholarshaveinvestigatedthegenerationandpropa... | Xu, Guoyuan Gu, Desheng | 1999 | 中国有色金属学会会刊:英文版1999，9，2： | 2 |
| 20 | Nanostructured strategies towards boosting organic lithium-ion batteries显示文摘Pursuing material development for next-generation batteries,organic electrode materials have shown great potential for lithium-ion batteries.However,their widespread adopting is plagued by intrinsic problems such as poor electronic conductivity,high dissolution inside electrolytes and unstable chemical peculiarity.Recently,nanostructured-strategies promoted organic electrodes with exotic properties for enhancing electron and ion transport together with the stability during electrochemical process,have received increasing attention and have been extensive applied in boosting the organic lithium-ion based energy storage.In this review,we summarize the applications of nanostructures to improve the performance of both organic anodes and cathodes,including(i)nanoscale design of zero-dimensional organic electrode materials,(ii)strategies of one-dimensional nanostructured organic electrode materials,(iii)construction of two-dimensional nanosized organic composite electrodes,and(iv)three-dimensional exploration of nanosized organic electrodes.We hope to stimulate high-quality applied research on understanding and handling the relationship between the nanostructure and performance of organic lithium-ion batteries that might speed up the commercialization of organic lithium ion batteries. | Yujing Liu Guoyuan Sun Xiaohan Cai Fan Yang Cong Ma Min Xue Xinyong Tao | 2021 | Journal of Energy Chemistry2021，30，3： | 2 |
您所在的机构暂未开通此部分的功能，请联系管理员