3篇
您的检索式：作者名="H.V.Atkinson"
|
|
|
题名
|
作者
|
年代
|
出处
|
被引量
|
| 1 | Microstructure and Mechanical Properties of 7005 Aluminum Alloy Components Formed by Thixoforming显示文摘In the present research, semisolid billet of 7005 aluminum alloy was fabricated by using recrystallization and partial remelting(RAP), then thixoformed at different isothermal temperatures, preheating temperatures and load routes. Mechanical properties and microstructure of the thixoformed product were investigated. The results showed that microstructure achieved by three-step induction heating warm extruded 7005 aluminum alloy consists of a uniform and spheroidal microstructure suitable for thixoforming.Preheating temperature of the die affected signi?cantly the ?lling status of semisolid billet of 7005 aluminum alloy. Complete ?lling status with good surface quality was obtained at a preheating temperature of 365 °C. Thixoformed microstructures consisting of relatively spheroidal grains illustrate the dependence of ?lling process on the sliding and rotating of solid grains rather than plastic deformation of solid grains. A non-uniform distribution of liquid phase was found in the different regions of the thixoformed product due to the slower adjustable velocity of solid grains as compared with liquid phase. Increase of isothermal temperatures led to a slight decrease of mechanical properties of the thixoformed product due to coarsening of solid grains. The highest yield strength, ultimate tensile strength and elongation of thixoformed components with T6 heat treatment are 237 MPa, 361 MPa and 16.8%, respectively, which were achieved at the isothermal temperature of 605 °C. Load route has a signi?cant effect on mechanical properties and microstructure of the thixoformed product. Defects, such as crack and microporosity occurred in the microstructure of the thixoformed product obtained under load route 2. It led to an obvious reduction of mechanical properties as compared with route 1. A better compatibility of deformation caused by more liquid fraction at the isothermal temperature of 612 °C is bene?cial to reducing nonuniformity of liquid phase in the different regions of the thixoformed product. | Jufu Jiang H.V.Atkinson Ying Wang | 2017 | Journal of Materials Science & Technology2017，33，4： | 7 |
| 2 | Coarsening rate of microstructure in semi-solid aluminium alloys显示文摘The rate of microstructural coarsening of recrystallisation and partial melting (RAP) and cooling slope (CS) processed materials in the semi-solid state is compared with rates found in the literature.The rate of coarsening depended on the liquid fraction but RAP route 2014 alloy with 37% liquid coarsened slightly more slowly than the CS route 2014 alloy with a lower liquid fraction of 17%, contrary to expectations.For the CS route, an increase in liquid fraction resulted in faster coarsening.A modified 2014 alloy with Fe, Mn and Zn stripped out of the composition gave a relatively high coarsening rate.The coarsening rate was also relatively high for CS 201 alloy in comparison with either RAP 2014 or CS 2014.Low coarsening rates are thought to be associated with the presence of particles which inhibit the migration of liquid film grain boundaries.This could be the result of pinning or of the liquid film impeding diffusion at the boundary. | H.V.ATKINSON D.LIU | 2010 | Transactions of Nonferrous Metals Society of China2010，20，9： | 4 |
| 3 | A review on steel thixoforming显示文摘Steel is a particularly challenging material to semi-solid process because of the high temperatures involved and the potential for surface oxidation.Here,the experience of semi-solid processing is reviewed and the current situation in relation to commercial application is assessed.The review will include discussion of the range of potential steel materials which are amenable to thixoformingn and identification of suitable steels;modelling of die fill and rheological properties of semi solid steel;technology considerations for industrialisation;die development and the properties of thixoformed products. | A.RASSILI H.V.ATKINSON | 2010 | 中国有色金属学会会刊:英文版2010，20，S3： | 3 |
您所在的机构暂未开通此部分的功能，请联系管理员