|
|
|
题名
|
作者
|
年代
|
出处
|
被引量
|
| 1 | Influence of Tip Clearance on Unsteady Flow in Automobile Engine Pump显示文摘The automobile engine pump is an important part of the automobile cooling system,and has a direct influence on the engine performance.Based on the SST k-ωturbulence model,unsteady numerical simulation for an automobile engine pump with different tip clearances was carried out by Fluent.To study the flow field characteristics and pressure fluctuation,the characteristics of secondary flow distribution in volute are also analyzed.The result shows that the pressure fluctuation characteristics of the flow field show obvious periodic variation at different levels of tip clearances.The peak value of pressure fluctuation at each monitoring point is dependent on the blade frequency.At the same time,with the increase of the tip clearance,the pressure fluctuation in the blade and volute is gradually increased,while the pressure fluctuation at the tip is reduced clearance.The pressure gradient in the pump also varies periodically with the rotation of the impeller.With the increase of the tip clearance,the pressure of the impeller,volute and tip clearance is gradually decreased.There are secondary flow vortexes inside the impeller,volute outlet and volute section.With the increase of tip clearance,the vortex intensity in the impeller channel is weakened,and the vortex strength at the volute outlet is intensified.On the cross section of the volute,the morphology of most vortexes has insignificant changes,but the vortex intensity decreased. | Jiacheng Dai Jiegang Mou Tao Liu | 2020 | Fluid Dynamics & Materials Processing2020，16，2： | 3 |
| 2 | Investigation of Self-Priming Process of a Centrifugal Pump with Double Blades显示文摘The gas-liquid two-phase flow patterns of a centrifugal pump during the self-priming process were investigated numerically and experimentally.The Euler-Euler multiphase model and SST k-ω turbulence model were applied for simulating the self-priming process.Meanwhile,the changes of motor speed and self-priming height were considered in the simulation.The overall transient two-phase flow features and water level distributions were mapped.Results showed that the self-priming process was divided into three stages.The liquid level in inlet-pipe rose in oscillation during self-priming process.The variations of water level during self-priming process of numerical simulation and test result agreed well.The inlet-pipe(Ver)was filled at 22 s and 24 s respectively numerically and experimentally.The bubble cloud circulated in the volute during middle stage of self-priming process,and breakup into smaller bubbles by shear force and tongue,and then discharged into chamber.The bubbles in the outlet-pipe mainly included bubbly flow and slug flow at the last stage of self-priming process,which is morphologically consistent with the test results.Also,during the self-priming process,the reflux liquid was pressed by blades and fully mixed with gas;that is the way to realizing the function of self-priming. | QIAN Heng MOU Jiegang REN Yun ZHU Zhibing LIU Nuojia ZHENG Shuihua WU Denghao | 2021 | Journal of Thermal Science2021，30，3： | 3 |
| 3 | Unsteady Flow and Structural Behaviors of Centrifugal Pump under Cavitation Conditions显示文摘Cavitation has a significant e ect on the flow fields and structural behaviors of a centrifugal pump. In this study, the unsteady flow and structural behaviors of a centrifugal pump are investigated numerically under di erent cavitation conditions. A strong two-way coupling fluid-structure interaction simulation is applied to obtain interior views of the e ects of cavitating bubbles on the flow and structural dynamics of a pump. The renormalization-group k-ε turbulence model and the Zwart–Gerbe–Belamri cavitation model are solved for the fluid side, while a transient structural dynamic analysis is employed for the structure side. The di erent cavitation states are mapped in the head-net positive suction head(H-NPSH) curves and flow field features inside the impeller are fully revealed. Results indicate that cavitating bubbles grow and expand rapidly with decreasing NPSH. In addition, the pressure fluctuations, both in the impeller and volute, are quantitatively analyzed and associated with the cavitation states. It is shown that influence of the cavitation on the flow field is critical, specifically in the super-cavitation state. The e ect of cavitation on the unsteady radial force and blade loads is also discussed. The results indicate that the averaged radial force increased from 8.5 N to 54.4 N in the transition progress from an onset cavitation state to a super-cavitation state. Furthermore, the structural behaviors, including blade deformation, stress, and natural frequencies, corresponding to the cavitation states are discussed. A large volume of cavitating bubbles weakens the fluid forces on the blade and decreases the natural frequencies of the rotor system. This study could enhance the understanding of the e ects of cavitation on pump flow and structural behaviors. | Denghao Wu Yun Ren Jiegang Mou Yunqing Gu Lanfang Jiang | 2019 | Chinese Journal of Mechanical Engineering2019，32，1： | 3 |
| 4 | Influence of the Area of the Reflux Hole on the Performance of a Self-Priming Pumnp显示文摘The self-priming process of a pump involves a complex gas-liquid two-phase flow.Studying the distribution of gas and water and the evolution of their flow in the pump is of great importance to optimize this process and shorten the pump self-priming time.In the present study,a standard k-εturbulence model and a multiphase flow model have been used to simulate the self-priming pump process considering four different reflux hole areas.A comparison of the distribution of air and water distribution on the axial surface and inside the volume have been carried out for the different considered cases.The pattern formed by the streamlines at different times during the whole self-priming process has also been investigated.The results show that the velocity at the trailing edge of the impeller outlet is the largest.The flow in the pump cavity is.complicated by the formation of vortices.The number,shape and location of the vortices change depending on the considered configuration. | Jiegang Mou Fengye Zhang Haoshuai Wang Denghao Wu | 2019 | Fluid Dynamics & Materials Processing2019，15，3： | 1 |
| 5 | Influences ofjet flow on cavitation performance显示文摘 | GU Yunqing DAI Dongshun MOU Jiegang | 2015 | World Pumps2015，2015，11： | 1 |
| 6 | Effects of Particle Concentration on the Dynamics of a Single-Channel Sewage Pump under Low-Flow-Rate Conditions显示文摘Single-channel sewage pumps are generally used to transport solid-liquid two-phase media consisting of a fluid and solid particles due to the good non-clogging property of such devices.However,the non-axisymmetric structure of the impeller of this type of pumps generally induces flow asymmetry,oscillatory outflow during operations,and hydraulic imbalance.In severe cases,these effects can jeopardize the safety and stability of the overall pump.In the present study,such a problem is investigated in the framework of a Mixture multiphase flow method coupled with a RNG turbulence model used to determine the structure of the flow field and the related motion of transported particles.It is shown that under different inlet particle concentrations,the flow field in the pump exhibits periodic variations of the pressure.The volume fraction of solid particles at the trailing edge of the suction surface of the blade is the largest,and solid particles tend to be concentrated at the outer edge of the pump body.With a rise in import particle content,the pressure and volume fraction of particles in the sewage pump also increase;for a fixed inlet particle concentration,the pressure pulsation amplitude increases with an increase in the flow rate.In addition,under small flow conditions,as the inlet particle concentration increases,the flow field leaving the sewage pump diaphragm near the outlet of the volute becomes more turbulent,and even a secondary back-flow vortex appears. | Peijian Zhou Chaoshou Yan Lingfeng Shu Hao Wang Jiegang Mou | 2021 | Fluid Dynamics & Materials Processing2021，17，5： | 0 |
| 7 | A Numerical Investigation on the Characteristics of the Radial Force in a Cycloid Gerotor Pump显示文摘In order to improve the performances of a cycloid gerotor pump,the variations of the radial force induced by different rotating speeds and outlet pressures are analyzed numerically.Using the numerical simulations as a basis,an improved oil inlet and outlet groove structure is proposed.The results show that the radial force decreases with the decrease of the outlet pressure and of the rotor speed.Compared with the original model,the large-end oil inlet line and pressure line of the new oil groove are claw-shaped.This configuration can effectively weaken the pressure changes inside the gerotor pump and reduce accordingly the radial force on the inner rotor. | Lingzhi Yu Yunqing Gu Jiegang Mou Denghao Wu Zhenfu Chen Yun Ren | 2020 | Fluid Dynamics & Materials Processing2020，16，5： | 0 |
| 8 | LES Analysis of the Unsteady Flow Characteristics of a Centrifugal Pump Impeller显示文摘Stall phenomena increase the complexity of the internal flow in centrifugal pump impellers.In order to tackle this problem,in the present work,a large eddy simulation(LES)approach is applied to determine the characteristics of these unstable flows.Moreover,a vorticity identification method is used to characterize quantitatively the vortex position inside the impeller and its influencing area.By comparing the outcomes of the numerical simulations and experimental results provided by a Particle Image Velocimetry(PIV)technique,it is shown that an apparent“alternating stall”phenomenon exists inside the impeller when relatively small flow rate conditions are considered.The stall is generated near the suction side of the blade inlet,grows towards the high-pressure side of the blade in the circumferential direction,and gradually attenuates.As the flow rate decreases,the number of stalls remains unchanged,while the related influencing area and strength gradually increase and the circumferential velocity increases. | Ting Zhang Denghao Wu Shijun Qiu Peijian Zhou Yun Ren Jiegang Mou | 2022 | Fluid Dynamics & Materials Processing2022，18，5： | 0 |
您所在的机构暂未开通此部分的功能，请联系管理员