|
|
|
题名
|
作者
|
年代
|
出处
|
被引量
|
| 1 | A promising new class of irradiation tolerant materials:Ti_2ZrHfV_(0.5)Mo_(0.2) high-entropy alloy显示文摘Recently, high-entropy alloys(HEAs) or multi-principal-element alloys with unprecedented physical,chemical, and mechanical properties, have been considered as candidate materials used in advanced reactors due to their promising irradiation resistant behavior. Here, we report a new single-phase bodycentered cubic(BCC) structured Ti_2 ZrHfV_(0.5)Mo_(0.2) HEA possessing excellent irradiation resistance, i.e.,scarcely irradiation hardening and abnormal lattice constant reduction after helium-ion irradiation,which is completely different from conventional alloys. This is the first time to report the abnormal XRD phenomenon of metallic alloys and almost no hardening after irradiation. These excellent properties make it to be a potential candidate material used as core components in next-generation nuclear reactors. The particular irradiation tolerance derives from high density lattice vacancies/defects. | Yiping Lu Hefei Huang Xuzhou Gao Cuilan Ren Jie Gao Huanzhi Zhang Shijian Zheng Qianqian Jin Yonghao Zhao Chenyang Lu Tongmin Wang Tingju Li | 2019 | Journal of Materials Science & Technology2019，35，3： | 23 |
| 2 | Hydrometallurgical purification of metallurgical grade silicon显示文摘The effects of the particle size of ground metallurgical grade silicon (MG-Si), the sort of acids, and the type of stirring on the purified efficiency of MG-Si were investigated. It was found that a particle size less than 0.1 mm was most effective for acid leaching; the extraction yield of impurities was increased by 9% with HF leaching compared with HCl leaching and HNO3 leaching, and increased by 7% with ultrasonic stirring compared with mechanical stirring. The principle of hydrometallurgical purification of metallurgical grade silicon under ultrasonic fields was also discussed. | MA Xiaodong ZHANG Jian WANG Tongmin LI Tingju | 2009 | Rare Metals2009，28，3： | 20 |
| 3 | Effect of Niobium on Microstructure and Properties of the CoCrFeNb_xNi High Entropy Alloys显示文摘A series of CoCrFeNb_xNi(x values in molar ratio, x = 0, 0.25, 0.45, 0.5, 0.75, 1.0 and 1.2) high entropy alloys(HEAs) was prepared to investigate the alloying effect of Nb on the microstructures and mechanical properties. The results indicate that the prepared CoCrFeNb_xNi(x > 0) HEAs consist of a simple FCC solid solution phase and a Laves phase. The microstructures of the alloys change from an initial single-phase FCC solid solution structure(x = 0) to a hypoeutectic microstructure(x = 0.25), then to a full eutectic microstructure(x = 0.45) and finally to a hypereutectic microstructure(0.5 < x < 1.2). The compressive test results show that the Nb0.45(x = 0.45) alloy with a full eutectic microstructure possesses the highest compressive fracture strength of 2558 MPa and a fracture strain of 27.9%. The CoCrFeNi alloy exhibits an excellent compressive ductility, which can reach 50% height reduction without fracture. The Nb0.25 alloy with a hypoeutectic structure exhibits a larger plastic strain of 34.8%. With the increase of Nb content, increased hard/brittle Laves phase leads to a decrease of the plasticity and increases of the Vickers hardness and the wear resistance. The wear mass loss, width and depth of wear scar of the Nb1.2(x = 1.2) alloy with a hypereutectic structure are the lowest among all alloy systems, indicating that the wear resistance of the Nb1.2 alloy is the best one. | Hui Jiang Li Jiang Dongxu Qiao Yiping Lu Tongmin Wang Zhiqiang Cao Tingju Li | 2017 | Journal of Materials Science & Technology2017，33，7： | 15 |
| 4 | Anomalous microstructure and tribological evaluation of AlCrFeNiW_(0.2)Ti_(0.5)high-entropy alloy coating manufactured by laser cladding in seawater显示文摘To evaluate the potential of high entropy alloys for marine applications,a new high entropy alloy coating of AlCrFeNiW_(0.2)Ti_(0.5)was designed and produced on Q235 steel via laser cladding.The microstructure,microhardness and tribological performances sliding against YG6 cemented carbide,GCr15 steel and Si_(3)N_(4)ceramic in seawater were studied in detail.The AlCrFeNiW_(0.2)Ti_(0.5)coating showed an anomalous’sunflower-like’morphology and consisted of BCC and ordered B2 phases.The microhardness was approximately 692.5 HV,which was 5 times higher than substrate.The coating showed more excellent tribological performances than Q235 steel and SUS304,a typical material used in seawater environment,sliding against all three coupled balls in seawater.Besides,the wear and friction of AlCrFeNiW_(0.2)Ti_(0.5)coating sliding against YG6 in seawater were most mild.The main reason was the generation of Mg(OH)_(2),CaCO_(3),metal oxides and hydroxides and the formation of protective tribo-film on the worn surface of AlCrFeNiW_(0.2)Ti_(0.5)coating in the process of reciprocated sliding.This would effectively hinder the direct contact between the worn surfaces of AlCrFeNiW_(0.2)Ti_(0.5)coating and YG6 ball,resulting in a decrease of friction coefficient and wear rate.Thus the YG6 was an ideal coupled material for AlCrFeNiW_(0.2)Ti_(0.5)coating in seawater,and the coating would become a promising wear-resisting material in ocean environment. | Hui Liang Dongxu Qiao Junwei Miao Zhiqiang Cao Hui Jiang Tongmin Wang | 2021 | Journal of Materials Science & Technology2021，，26： | 8 |
| 5 | On modeling approach for embedded real-time software simulation testing显示文摘Modeling technology has been introduced into software testing field. However, how to carry through the testing modeling effectively is still a diffculty. Based on combination of simulation modeling technology and embedded real-time software testing method, the process of simulation testing modeling is studied first. And then, the supporting environment of simulation testing modeling is put forward. Furthermore, an approach of embedded real-time software simulation testing modeling including modeling of cross-linked equipments of system under testing (SUT), test case, testing scheduling, and testing system service is brought forward. Finally, the formalized description and execution system of testing models are given, with which we can realize real-time, closed loop, and automated system testing for embedded real-time software. | Yin Yongfeng Liu Bin Zhong Deming Jiang Tongmin | 2009 | Journal of Systems Engineering and Electronics2009，20，2： | 6 |
| 6 | The influence of Sc addition on microstructure and tensile mechanical properties of Mg-4.5Sn-5Zn alloys显示文摘The microstructure and tensile properties of the as-cast and as-rolled Mg-4.5Sn-5Zn alloys by adding various Sc content were investigated.Improvement of the tensile properties in as-cast Sc-containing alloys is attributed to the grain refinement and modification of secondary phase morphology.Three types of precipitates,namely spherical Mg2Sn,rod-like MgZn and Sc-rich phases were dispersed in the matrix of the Sc added M g-4.5Sn-5Zn alloys after hot rolling deformation.In addition,weakening and deflecting of the basal texture in as-rolled alloys were found and were attributed to Sc addition.Further increasing the Sc addition rate to 0.4 wt.%,however,resulted in the clustering of the Sc-rich phases and was found to reduce the tensile properties of the alloy,especially the elongation.The as-rolled Mg-4.5Sn-5Zn-0.3Sc alloy exhibits an optimum combination of tensile properties.The ultimate tensile strength,yield strength and elongation are 293.0MPa,164.2Mpa and 21.5%,respectively,and the elongation is about 68%higher than that of Sc-free alloy. | Pengqi Wang Enyu Guo Xuejian Wang Huijun Kang Zongning Chen Zhiqiang Cao Tongmin Wang | 2019 | Journal of Magnesium and Alloys2019，7，3： | 6 |
| 7 | Enhanced antibacterial behavior of a novel Cu-bearing high-entropy alloy显示文摘Contact infection of bacteria and viruses has been a critical threat to human health. The worldwideoutbreak of COVID-19 put forward urgent requirements for the research and development of the selfantibacterial materials, especially the antibacterial alloys. Based on the concept of high-entropy alloys, thepresent work designed and prepared a novel Co_(0.4)FeCr_(0.9)Cu_(0.3) antibacterial high-entropy alloy with superior antibacterial properties without intricate or rigorous annealing processes, which outperform the antibacterial stainless steels. The antibacterial tests presented a 99.97% antibacterial rate against Escherichiacoli and a 99.96% antibacterial rate against Staphylococcus aureus after 24 h. In contrast, the classic antibacterial copper-bearing stainless steel only performed the 71.50% and 80.84% antibacterial rate, respectively. The results of the reactive oxygen species analysis indicated that the copper ion release and theimmediate contact with copper-rich phase had a synergistic effect in enhancing antibacterial properties.Moreover, this alloy exhibited excellent corrosion resistance when compared with the classic antibacterialstainless steels, and the compression test indicated the yield strength of the alloy was 1015 MPa. Thesefindings generate fresh insights into guiding the designs of structure-function-integrated antibacterial alloys. | Guangyu Ren Lili Huang Kunling Hu Tianxin Li Yiping Lu Dongxu Qiao Haitao Zhang Dake Xu Tongmin Wang Tingju Li Peter K.Liaw | 2022 | Journal of Materials Science & Technology2022，，22： | 6 |
| 8 | Mechanical Properties Improvement of AlCrFeNi_2Ti_(0.5) High Entropy Alloy through Annealing Design and its Relationship with its Particle-reinforced Microstructures显示文摘High entropy alloy has attracted increasing attentions.However,to enhance the alloy strength often leads to impairment of the ductility,or vice versa.Here we reported a heat treatment approach on AlCrFeNi2Ti0.5 high entropy alloy,which can elevate the strength and ductility simultaneously.An ingot of AlCrFeNi2Ti0.5 weighing 2.5 kg was firstly fabricated by medium frequency induction melting.Then samples from the same height of the bulk ingot were annealed for 6 h at 600,700,800 and 1000 ℃,respectively.After 1000 ℃ annealing,an optimal microstructure was obtained by using our approach which can make some precipitation particles distribute homogeneously in the dendrite interior while keep the interdendrite structure as a single solid solution phase.The mechanical test on this AlCrFeNi2Ti0.5 alloy sample showed that,the compressive fracture strength σbc was increased by about600 MPa and the plastic strain ep was doubled,compared with those of the as-cast sample.Our approach can be readily adapted to large-scale industrial production of high entropy alloys with high strength and ductility by proper annealing treatment. | Li Jiang Hui Jiang Yiping Lu Tongmin Wang Zhiqiang Cao Tingju Li | 2015 | Journal of Materials Science & Technology2015，31，4： | 6 |
| 9 | High Throughput Sequencing of circRNAs in Tomato Leaves Responding to Multiple Stresses of Drought and Heat显示文摘Our aim is to study the roles of a new emerging group of non-coding RNAs, circRNAs, in tomato(Solanum lycopersicum L.) plants grown at the combination of drought and heat, two of the most usual stress conditions known to frequently happen in field. Tomato seedlings from cultivar‘Jinling Meiyu’ were treated without stresses(control), at water shortage, high temperature and subjected the multiple stresses. In total, 467 circRNAs were identified with 87.82% from exon using high throughput sequencing technology. Among the circRNAs, 70 were from chr1 with the range from 23 to 49 from the other chromosomes. In detail, 156 circRNAs were shared in the four libraries, while 21, 17 and 36 circRNAs were only shown in drought, heat and multiple stresses libraries, respectively. Through a differential expression analysis, four, seven and nine circRNAs were differentially regulated in tomato at drought, heat and multiple stresses as compared with control. These circRNAs played roles on photosynthesis, starch and sucrose metabolism, RNA transport, RNA degradation, spliceosome, ribosome, etc. Our study underlined the potential role of circRNAs involved in the abiotic stress response in tomato, which might pave the way for studying biological roles of circRNAs responding to multiple stresses in plants. | Rong Zhou Xiaqing Yu Carl-Otto Ottosen Tongmin Zhao | 2020 | Horticultural Plant Journal2020，6，1： | 5 |
| 10 | Grain nucleation and growth behavior of a Sn-Pb alloy affected by direct current: An in situ investigation显示文摘In situ synchrotron X-ray radiography was used to study the effect of direct current(DC) on the grain nucleation and growth of Sn-50 wt.%Pb alloy. The results showed that applying DC adequately during solidification could effectively enhance the grain nucleation and inhibit its growth. Imaging of comparative experiments with varying DC intensity indicated that the final grain size, determined by the competition between grain nucleation and growth, was sensitively dependent on the DC intensity. It was found that the average grain size was decreased from 1632 to 567 μm with DC density of 1.5 A/mm^2 compared to the case without DC. Beyond this value, raising the current density may cause a significant decrease in the nucleation rate, and thus lead to a coarsening of the grain structure. | Fenfen Yang Zongning Chen Fei Cao Rong Fan Huijun Kang Wanxia Huang Qingxi Yuan Tiqiao Xiao Yanan Fu Tongmin Wang | 2017 | Journal of Materials Science & Technology2017，33，10： | 5 |
| 11 | Microstructure and mechanical properties of C_(x)Hf_(0.25)NbTaW_(0.5) refractory high-entropy alloys at room and high temperatures显示文摘The microstructure and mechanical properties of as-cast and isothermally annealed C_(x)Hf_(0.25)NbTaW_(0.5)(x=0,0.05,0.15,0.25)refractory high-entropy alloys(RHEAs)were studied.Both the as-cast and annealed RHEAs consisted of disordered body-centered cubic solid solution phase and metal carbide(MC)phase with a face-centered cubic crystal structure(Fm-3 m space group).The primary carbides were enriched with Hf and C elements and tended to form lamellar eutectic-like microstructure in the interdendrites.The lamellar eutectic-like structure in the interdendrites would be formed from the decomposition of sub-carbide M_(2)C under the influence of Hf element.After isothermal annealing,slatted carbides were precipitated on the matrix,and the distribution became more uniform with high C content.The formation of carbides strongly influenced the mechanical properties both at room and high temperatures.The yield strength values of C_(x)Hf_(0.25)NbTaW_(0.5) RHEA at 1473 and 1673 K were 792 and 749 MPa,respectively.The result had exceeded the high temperature mechanical properties of currently known RHEAs.Moreover,this RHEA exhibited high-temperature performance stability and excellent plasticity,exceeding 30 and 50%at room and elevated temperatures(above 1273 K),respectively.During thermal deformation,carbon-containing RHEAs obtained more severe work hardening than that of ACHO RHEAs,and required greater dynamic recrystallization to achieve the dynamic equilibrium. | Shiyu Wu Dongxu Qiao Haitao Zhang Junwei Miao Hongliang Zhao Jun Wang Yiping Lu Tongmin Wang Tingju Li | 2022 | Journal of Materials Science & Technology2022，，2： | 4 |
| 12 | Microstructural characteristics and mechanical behavior of B4Cp/6061Al composites synthesized at different hot-pressing temperatures显示文摘B4Cp/6061Al composites have become important structural and functional materials and can be fabricated by powder metallurgy and subsequent hot rolling. In this work, the effects of the hot-pressing temperature on microstructures and mechanical behaviors of the B4Cp/6061Al composites were investigated. The results showed that compared with the T4 heat treated B4Cp/6061Al composite hot pressed at 560℃, the yield strength and failure strain of the composites hot pressed at 580℃ were increased to 235 MPa and 18.4%, respectively. This was associated with the interface bonding strength between the B4C particles and the matrix. However, the reaction products, identified to be MgAl2O4 phases, were detected in the composites hot pressed at 600℃. The formation of the MgAl2O4 phases resulted in the Mg depletion, thus reducing the yield strength to 203.5 MPa after the T4 heat treatment due to the effect of the solid solution strengthening being weakened. In addition, the variation of hardness and electrical conductivity was mainly related to the Mg content in the matrix. Based on the as-rolled microstructures observed by SEM, SR-μCT and fracture surfaces, the deformation schematic diagram was depicted to reflect the tensile deformation process of the composites. | Minqiang Gao Zongning Chen Huijun Kang Enyu Guo Rengeng Li Ying Fu Honglan Xie Tongmin Wang | 2019 | Journal of Materials Science & Technology2019，35，8： | 4 |
| 13 | Ductile and ultrahigh-strength eutectic high-entropy alloys by large-volume 3D printing显示文摘1.Introduction Additive manufacturing or 3D printing outweighs conventional casting methods in the aspect of complex parts fabrication,which can realize one-step formation without the need of complicated cast dies.3D printing significantly promotes industrial production for making near-net shaped components.However,this promising technique is not always ideally applicable for metals and alloys.For example,titanium alloys prepared by 3D printing often suf-fer from poor plasticity,and usually require further complex heat treatment or hot isostatic pressing treatment,in order to remove internal stress and regulate plasticity and strength[1,2],which de-feats the original intention of employing additive manufacturing.One of the fundamental causes for such issues is the low fluidity of the alloys upon melting,leading to great chemical heterogeneity,high porosity content and residual stresses.This limitation hinders further design and fabrication of high-performance printable alloys from large scale production and application. | Yiping Lu Xiaoxiang Wu Zhenghong Fu Qiankun Yang Yong Zhang Qiming Liu Tianxin Li Yanzhong Tian Hua Tan Zhiming Li Tongmin Wang Tingju Li | 2022 | Journal of Materials Science & Technology2022，，31： | 4 |
| 14 | Mould taper optimization for continuous casting steels by numerical simulation显示文摘A transient,two-dimensional,coupled finite element model was employed to simulate the solidification and shrinkage of continuous casting steels by means of ANSYSTM.In the model,a gap-dependent heat transfer condition was introduced to modify the heat flux function,and the variations of material thermal properties,mechanical properties as well as the yield function with temperature were considered.The solidification and shrinkage processes of four round billets and two square billets were simulated by indirect coupled method.Simulation results show that carbon content,pouring temperature,casting speed and shape of billets have distinct influence on the solidification shrinkage of billets.Ideal continuous parabolic tapers were designed and optimized according to the calculated shrinkage curves of billets. | Wang Tongmin Cai Shaowu Li Jun Xu Jingjing Chen Zongning Zhu Jing Cao Zhiqiang Li Tingju | 2010 | China Foundry2010，7，1： | 4 |
| 15 | Influence of deformation on the corrosion behavior of LZ91 Mg-Li alloy显示文摘The effect of rolling and forging on the microstructure and corrosion behavior of LZ91 alloy was investigated using an electron probe micro-analyzer,immersion and electrochemical tests.Results showed that the area fraction of theβ-Li phase remained unchanged,and the grain size of theβ-Li phase decreased after forging.The as-rolled forged alloy(FR-LZ91)exhibited the highest area fraction of theβ-Li phase and the longest grains.The corrosion resistance of the forged LZ91 alloy increased due to grain refinement that prevented further corrosion during the immersion test.Among the experimental alloys,FR-LZ91 showed the highest resistance of corrosion film and charge transfer resistance values due to its protective film caused by the high area fraction of theβ-Li phase. | Xueqin Liu Xuejian Wang Enyu Guo Zongning Chen Huijun Kang Tongmin Wang | 2023 | International Journal of Minerals,Metallurgy and Materials2023，30，1： | 3 |
| 16 | Enhancing mechanical properties and corrosion resistance of nickel-aluminum bronze via hot rolling process显示文摘The mechanical properties and corrosion behavior of as-cast, as-annealed and hot-rolled nickelaluminum bronze(NAB) alloy(Cu-9 Al-10 Ni-4 Fe-1.2 Mn, all in wt.%) in 3.5 wt.% Na Cl solution were investigated. The results show that annealing introduces a large number of k phases to precipitate in the k phase. However, after further hot rolling, the original continuous k phases are spheroidized and dispersed, increasing the strength, hardness, and elongation of the alloy. In addition to the enhanced mechanical properties, the corrosion resistance of the NAB samples is also improved significantly by hot rolling, as revealed by the mass loss measurements, electrochemical impedance spectroscopy(EIS), and cross-sectional corrosion morphology. Selective phase corrosion occurs by the preferential corrosion of the k phase, which acts as an anode to the k phases, and the uncorroded k phases are retained in the corrosion product film. The interfaces between the k phases and the surrounding corrosion products become discontinuous caused by the spheroidization of k phases, reducing the corrosion of the substrate by the corrosive medium via the channels. As a result, the corrosion rate and the maximum local corrosion depth of the hot-rolled NAB sample are greatly reduced. | Yanhua Zeng Fenfen Yang Zongning Chen Enyu Guo Minqiang Gao Xuejian Wang Huijun Kang Tongmin Wang | 2021 | Journal of Materials Science & Technology2021，，2： | 3 |
| 17 | Microwave absorption performance of FeCoNiAlCr_(0.9)alloy powders by adjusting the amount of process control agent显示文摘Different amounts of absolute ethanol(0-50 mL)are used as process control agents(PCA)to prepare FeCoNiAlCr0.9 high entropy alloy(HEA)powders via 90 h ball milling.The results show that the increased amount of PCA plays an active role in the crystallinity of powders,and regulate the thickness and size distribution of flake particles.As the volume of PCA increases,the real and imaginary parts(ε′andε″)of complex permittivity get increased by the enhancement of the interface polarization and surface polarization,while the increase in the real and imaginary parts(μ′andμ″)of complex permeability arises from the increased anisotropic energy.The addition of PCA not only promotes the reflection loss but also extends the effective bandwidth(up to 4.28 GHz).Here,the performance adjustment of HEA electromagnetic absorber is realized by forthrightly changing the process parameters of ball milling. | Yuping Duan Huifang Pang Xin Wen Xuefeng Zhang Tongmin Wang | 2021 | Journal of Materials Science & Technology2021，，18： | 3 |
| 18 | Composition,Microstructure,Phase Constitution and Fundamental Physicochemical Properties of Low-Melting-Point Multi-Component Eutectic Alloys显示文摘Low-melting-point alloys have an extensive applications in the fields of materials processing, phase change energy storage, electronic and electrical automatic control, continuous casting simulation, welding, etc.Specifically, the eutectic compositions make up a large number of low-melting-point alloys that are exploited because of their desirable features like single melting peaks, excellent operational reliability, and casting fluidity. However, the fundamental physicochemical properties from the current available literature on low-melting-point multi-component eutectic alloys(LMP-MCEAs) are rather rare and lowly accurate, including the exact melting temperatures and compositions, constituent phases, microstructures and morphologies, melting enthalpies, specific heats, densities, and so on. This lack of information seriously limits the development and application of low-melting-point multi-component eutectic alloys.In this paper, the low-melting-point multi-component eutectic alloys composed of Bi, Cd, Sn, Pb, and In elements synthesized by high vacuum induction melting and fundamental data were investigated by scanning electron microscopy(SEM), energy dispersive spectrometry(EDS), X-ray diffraction(XRD), differential scanning calorimetry(DSC), and density analysis instrument. Most of the LMP-MCEAs with complex eutectic morphology structures and XRD diffraction patterns could be explained with the fact that they were three-phase eutectic alloys with mixed growth way. Generally, LMP-MCEAs present an extremely low melting point between 48.3 and 124 °C and high density between 8 and 10 g/cm3. | Kaiyao Zhou Zhongyi Tang Yiping Lu Tongmin Wang Haipeng Wang Tingju Li | 2017 | Journal of Materials Science & Technology2017，33，2： | 3 |
| 19 | Improving the resistance of the rice PTGMS line Feng39S by pyramiding blast,bacterial blight,and brown planthopper resistance genes显示文摘Knowledge of rice(Oryza sativa L.)genes and various DNA markers can be used in genomic breeding programs aimed at developing improved elite rice cultivars.We used an efficient genomic breeding approach to pyramid four resistance genes(Pi2,Xa23,Bph14,and Bph15)in the popular photoperiod-and thermosensitive genic male sterile(PTGMS)rice line Feng39S.We performed foreground selection for the target genes,followed by recombinant selection and background selection.This process reduced the sizes of the genomic segments harboring the target genes(566.8 kb for Pi2,1143.9 kb for Xa23,774.7 kb for Bph14,and 1574.9 kb for Bph15)and accelerated the recovery of the recurrent parent genome to proportions ranging from 98.77%to 99.16%,thus resulting in four near-isogenic lines.To assemble the four resistance genes in Feng39S,we performed a double-way cross combined with foreground and background selection to generate two improved lines of Feng39S(Pi2+Xa23+Bph14+Bph15)with a recurrent parent genome recovery of 98.98%.The two lines showed agronomic performance,grain quality,and fertility–sterility transition characteristics similar to those of the original Feng39S line.The newly developed PTGMS lines and corresponding hybrid combinations were resistant to various field blast isolates and seven representative isolates of bacterial blight.At the seedling stage,the lines also showed resistance against brown planthopper.This study provides an efficient and accurate genomic breeding approach for introducing desirable traits into PTGMS lines. | Dabing Yang Lizhong Xiong Tongmin Mou Jiaming Mi | 2022 | The Crop Journal2022，10，4： | 3 |
| 20 | Optimum design of equivalent accelerated life testing plans based on proportional hazards-proportional odds model显示文摘The optimum design of equivalent accelerated life testing plan based on proportional hazards-proportional odds model using D-optimality is presented.The defined equivalent test plan is the test plan that has the same value of the determinant of Fisher information matrix.The equivalent test plan of step stress accelerated life testing(SSALT) to a baseline optimum constant stress accelerated life testing(CSALT) plan is obtained by adjusting the censoring time of SSALT and solving the optimization problem for each case to achieve the same value of the determinant of Fisher information matrix as in the baseline optimum CSALT plan.Numerical examples are given finally which demonstrate the equivalent SSALT plan to the baseline optimum CSALT plan reduces almost half of the test time while achieving approximately the same estimation errors of model parameters. | Tingting Huang Tongmin Jiang | 2011 | Journal of Systems Engineering and Electronics2011，22，5： | 3 |
您所在的机构暂未开通此部分的功能，请联系管理员