|
|
|
题名
|
作者
|
年代
|
出处
|
被引量
|
| 1 | Hydrogen storage properties of Zr_(1-x)Ti_xCo intermetallic compound显示文摘The intermetallic compound Zr1-xTixCo was prepared and its suitability for hydrogen storage was investigated. The alloys obtained by magnetic levitation melting with the composition of Zr1-xTixCo (x=0, 0.1, 0.2 and 0.3, at.%) show single cubic phase by X-ray diffraction. A single sloping plateau was observed on each isothermal, and pressure-composition-temperature (PCT) measurement results show that the equilibrium hydrogen desorption pressure of Zr1-xTixCo alloy increases with increasing Ti content. The desorption temperatures for supplying 100 kPa hydrogen are about 665, 642, 621 and 614 K for ZrCo, Zr0.9Ti0.1Co, Zr0.8Ti0.2Co and Zr0.7Ti0.3Co alloy, respectively. Repeated hydrogen absorption and desorption cycles do not generate separated ZrCo, TiCo and ZrH2 phases, indicating that alloys have good thermal and hydrogen stabilization. | HUANG Zhuo LIU Xiaopeng JIANG Lijun WANG Shumao | 2006 | Rare Metals2006，25，z2： | 7 |
| 2 | Hierarchical nanostructured composite cathode with carbon nanotubes as conductive scaffold for lithium-sulfur batteries显示文摘Carbon nanotubes (CNTs) are excellent scaffolds for advanced electrode materials, resulting from their intrinsic sp2 carbon hybridization, interconnected electron pathway, large aspect ratio, hierarchical porous structures, and low cost at a large-scale production. How to make full utilization of the mass produced CNTs as building blocks for nanocomposite electrodes is not well understood yet. Herein, a composite cathode containing commercial agglomerated multi-walled CNTs and S for Li-S battery was fabricated by a facile melt-diffusion strategy. The hierarchical CNT@S coaxial nanocables exhibited a discharging capacity of 1020 and 740 mAh g-1 at 0.5 and 2.0 C, respectively. A rapid capacity decay of 0.7% per cycle at the initial 10 cycles and a slow decay rate of 0.14% per cycle for the later 140 cycles were detected. Such hierarchical agglomerated CNT@S cathodes show advantages in easy fabrication, environmentally benign, low cost, excellent scalability, and good Li ion storage performance, which are extraordinary composites for high performance Li-S battery. | Xiaofei Liu Qiang Zhang Jiaqi Huang Shumao Zhang Hongjie Peng Fei Wei | 2013 | Journal of Energy Chemistry2013，22，2： | 6 |
| 3 | Preparation and thermal stability on non-vacuum high temperature solar selective absorbing coatings显示文摘Spectrally selective TiAl/TiAlN/TiAlON/TiAlO coating was deposited on stainless steel and copper substrates using a multiarc ion plating system.The structure,morphology,optical reflectance and electrical resistivity were investigated by X-ray diffraction(XRD),scanning electron microscopy(SEM),spectrophotometer and four-point probe meter,respectively.The results show that the coating exhibits high absorptance(―0.9) and low emittance(0.09―0.19).The coating remains stable in air up to 650℃ for 1h.These properties are of extraordinary interest in solar thermal power generations and energy saving buildings. | HAO Lei WANG ShuMao JIANG LiJun LIU XiaoPeng LI HuaLing LI ZhiNian | 2009 | Chinese Science Bulletin2009，54，8： | 6 |
| 4 | Joint Resource Allocation and Coordinated Computation Offloading for Fog Radio Access Networks显示文摘The cloud radio access network(C-RAN) and the fog computing have been recently proposed to tackle the dramatically increasing traffic demands and to provide better quality of service(QoS) to user equipment(UE).Considering the better computation capability of the cloud RAN(10 times larger than that of the fog RAN) and the lower transmission delay of the fog computing,we propose a joint resource allocation and coordinated computation offloading algorithm for the fog RAN(F-RAN),which takes the advantage of C-RAN and fog computing.Specifically,the F-RAN splits a computation task into the fog computing part and the cloud computing part.Based on the constraints of maximum transmission delay tolerance,fronthaul and backhaul capacity limits,we minimize the energy cost and obtain optimal computational resource allocation for multiple UE,transmission power allocation of each UE and the event splitting factor.Numerical results have been proposed with the comparison of existing methods. | Kai Liang Liqiang Zhao Xiaohui Zhao Yong Wang Shumao Ou | 2016 | China Communications2016，13，S2： | 4 |
| 5 | Thermal stability of nitride solar selective absorbing coatings used in high temperature parabolic trough current显示文摘This paper reports a new efficient solar selective surface in high temperature application.The influence of the monolayer's microstructure and deposition rate was firstly discussed.Then the nitride nano-multilayer on the polished stainless steel (herein after referred as 'SS') substrate was prepared with Ti and Al metal targets by DC.and R.F.magnetron co-sputtering.The samples were annealed in air at different temperatures ranging from 350 to 800°C for 2 h to evaluate their thermal stability.The samples' surface and cross-section morphology,crystal structure,phase composition,optical properties were analyzed by scanning electron microscopy,X-ray diffraction,UV-VIS-NIR spectrophotometer and infrared emissivity tester.The results show that the coatings exhibit high solar selectivity (α/ε) of 0.943/0.08 even after heat-treatment up to 400°C for 2 h in air.After heat-treatment at 600°C in air,the solar selectivity decreases to 0.92/0.16. | HAO Lei,DU Miao,LIU XiaoPeng,WANG ShuMao,JIANG LiJun,Lü Fang,LI ZhiNian & MI Jing Department of Energy Material and Technology,General Research Institute for Nonferrous Metals,Beijing 100088,China | 2010 | Science China(Technological Sciences)2010，53，6： | 4 |
| 6 | Laves phase hydrogen storage alloys for super-high-pressure metal hydride hydrogen compressors显示文摘Ti-Cr- and Ti-Mn-based alloys were prepared to be low- and high-pressure stage metals for a double-stage super-high-pressure metal hydride hydrogen compressor. Their crystallographic characteristics and hydrogen storage properties were investigated. The alloy pair Ti0.9Zr0.1Mn1.4- Cr0.35V0.2Fe0.05/TiCr1.55Mn0.2Fe0.2 was optimized based on the comprehensive performance of the studied alloys. The product hydrogen with a pressure of 100 MPa could be produced from 4 MPa feed gas when hot oil was used as a heat reservoir. | GUO Xiumei WANG Shumao LIU Xiaopeng LI Zhinian LU Fang MI Jing HAO Lei JIANG Lijun | 2011 | Rare Metals2011，30，3： | 3 |
| 7 | Blautia producta displays potential probiotic properties against dextran sulfate sodium-induced colitis in mice显示文摘Blautia has attracted attention because of its potential efficacy in ameliorating host energy metabolism and inflammation.This study aims to investigate the influences of Blautia producta D4 on colitis induced by dextran sulfate sodium(DSS)and to reveal the underlying mechanisms.Results showed that B.producta D4 intervention significantly relieved body weight loss,and suppressed the elevation of pro-inflammatory cytokines(including interleukin-6(IL-6),tumor necrosis factor-α(TNF-α),and interleukin-1β(IL-1β))and excessive oxidative stress(myeloperoxidease(MPO)activity,superoxide dismutase(SOD)activity,glutathione peroxidase(GSH-Px)activity,and malondialdehyde(MDA)level)in colitis mice.Moreover,the concentrations of tight junction proteins(occludin,claudin-1,and ZO-1)related to the intestinal barrier were obviously elevated,and colitis-related TLR4/NF-κB pathway activation was remarkably inhibited after B.producta D4 intervention.The intestinal microbial disorder was evidently ameliorated by increasing the relative abundance of Clostridium sensu stricto 1,Bifidobacterium,GCA-900066225,Enterorhabdus,and reducing the relative abundance of Lachnospiraceae NK4A136 group.In conclusion,oral administration of B.producta D4 could ameliorate DSS-induced colitis by suppressing inflammatory responses,maintaining the intestinal barrier,inhibiting TLR4/NF-κB pathway,and regulating intestinal microbiota balance.These results are conducive to accelerate the development of B.producta D4 as a functional probiotic for colitis. | Bingyong Mao Weiling Guo Shumao Cui Qiuxiang Zhang Jianxin Zhao Xin Tang Hao Zhang | 2024 | Food Science and Human Wellness2024，13，2： | 3 |
| 8 | Enhancement of Ti-Cr-V BCC alloys on the dehydrogenation kinetics of Li-Mg-N-H hydrogen storage materials显示文摘The hydrogen storage properties of a Li-Mg-N-H material doped by a 4 mol.% Ti3Cr3V4 body centre cubic(BCC) alloy hydride and prepared with a ball-milling method were investigated by X-ray diffraction,scanning electron microscopy,transmission electron microscopy and Sievert's technology test.The results show that the Ti3Cr3V4 BCC alloy hydride/Li-Mg-N-H composite has good reversible hydrogen storage properties.The dehydrogenation kinetics of the Li-Mg-N-H system can be greatly improved by doping the Ti3Cr3V4 BCC alloy hydride.The composite desorbed 4.1 wt.% hydrogen in the first 60 min at 473 K under 0.1 MPa pressure,but when without the BCC alloy addition,only 3.0 wt.% hydrogen was desorbed under the same dehydrogenation condition.It can be deduced that the Ti3Cr3V4 BCC alloy uniformly distributed in the Li-Mg-N-H substrate could decrease the activating energy of hydrogen molecules to H atoms and increase H diffusion paths in the composite,enhancing the dehydrogenation kinetics of the Li-Mg-N-H system. | WANG Jingchuan,LI Zhinian,LI Hualing,MI Jing,Lü Fang,WANG Shumao,LIU Xiaopeng,and JIANG Lijun General Research Institute for Nonferrous Metals,Beijing 100088,China | 2010 | Rare Metals2010，29，6： | 3 |
| 9 | Cu2SnSe3/CNTs Composite as a Promising Anode Material for Sodium-ion Batteries显示文摘Metal selenides as anode materials for sodium-ion batteries have attracted considerable attention owing to their high theoretical specific capacities and variable composition and structures.However,the achievement of long cycle life and superior rate performance is challenging for these selenide materials due to the volume variation upon cycling.Herein,a composite composed of a new binary-metal selenide[Cu2SnSe3(CSS)]and carbon nanotubes(CNTs)was constructed via a hydrothermal process followed by calcination at 600℃.Benefited from the unique structure of binary-metal selenide and the conductive network of CNTs,the Cu2SnSe3/carbon nanotubes(CSS/CNT)composite exhibits excellent electrochemical performance when used as an anode material for sodium-ion batteries.A reversible specific capacity of 399 mA·h/g can be maintained at a current density of 100 mA/g even after 100 cycles.This work provides a promising strategy for rational design of binary-metal selenides upon delicate crystal phase control as electrode materials. | ANG Zuojun WU Xueyan MA Chao HOU Chengcheng XU Shumao WEI Xiao WANG Kaixue CHEN Jiesheng | 2020 | Chemical Research in Chinese Universities2020，36，1： | 2 |
| 10 | A promising trend for field information collection:An air-ground multi-sensor monitoring system显示文摘Timely identifying and quantifying significant spatial and temporal variability in agricultural field has been a crucial factor for improving agricultural production and management.This paper focuses on the mainstream techniques and applications can be adopted to improve the field information collection method.In this paper,the development of wireless sensor networks(WSNs)and remote sensing(RS)technology were reviewed,especially the micro unmanned aerial vehicle(mUAV)-based WSNs and mUAV-based RS by analyzing its applications in field information collection,and pointed out its existing benefits and limitations.A system encompassed multiple technique approaches was proposed in this paper which is called air-ground multi-sensor monitoring system.With the diversification methods of in-field information collection and the improvement of detection precision,an infield information collection system will play an important role in controlling the farming operations of mechanized agriculture and optimizing the management of agricultural machinery group.In the future,the combination of mUAV,WSNs and RS for crop and soil monitoring will become a powerful tool to obtain field information,increase production,optimize the overall farming practices and input of resources and provide comprehensive reference for the study of soil-crops-machine relationships. | Yawei Zhang Du Chen Shumao Wang Lei Tian | 2018 | Information Processing in Agriculture2018，5，2： | 2 |
| 11 | Effect of Manganese substitution on hydrogen storage properties of LaNi_(4.25-x)Al_(0.75)Mn_x alloy显示文摘The effect of Mn substitution on phase structure, hydrogen hydriding/dehydriding properties (plateau pressure and slope) and reaction heat enthalpy of LaNi4.25-xAl0.75Mnx alloys (x=0, 0.25, 0.35, 0.45, 0.55 and 0.65) were studied. The experimental results show that all LaNi4.25-xAl0.75Mnx alloys have single phase and have the same hexagonal structure as that of LaNi5 alloy (CaCu5 type, P6/mmm). With increasing Mn substitution content, the cell parameters of LaNi4.25-xAl0.75Mnx alloy greatly increase, but the maximum hydrogen storage capacity and the equilibrium absorption pressure of LaNi4.25-xAl0.75Mnx alloy decrease from 1.38 wt.% to 1.18 wt.% and from 1.61 to 0.0712 MPa, respectively. Moreover, the hydrogen pressure plateau slope factor σ increases from 0.014 to 0.18, but the hysteresis factor is nearly constant. The heat enthalpy absolute value |ΔHplat| increases from 46.7 kJ·mol-1 H2 to 56.1 kJ·mol-1 H2 as the Mn content x increases from 0 to 0.65. | JIANG Yuwei LIU Xiaopeng JIANG Lijun WANG Shumao YANG Hongguang | 2006 | Rare Metals2006，25，z2： | 2 |
| 12 | Designing appropriate heat treatment temperature for LaNi_(3.8)Al_(0.75)Mn_(0.45) alloy显示文摘The effect of heat treatment on microstructure, equilibrium hydrogen sorption pressure and plateau slope of LaNi3.8Al0.75Mn0.45 alloy was investigated. X-ray diffraction (XRD) analysis indicates that annealed alloys have single phase and the same hexagonal structure as that of LaNi5 alloy (CaCu5 type, P6/mmm). The cell parameters of alloys fluctuate with the increasing annealing temperature. The equilibrium hydrogen pressure and plateau slope are a parabola function with annealing temperature for LaNi3.8Al0.75Mn0.45 alloy. By this relationship, an appropriate heat treatment temperature for LaNi3.8Al0.75Mn0.45 alloy is determined to about 1220-1230 K by mathematic simulation process. However, the maximum hydrogen storage capacity of alloys does not affected by the annealing temperature. | JIANG Yuwei LIU Xiaopeng JIANG Lijun WANG Shumao YANG Hongguang | 2006 | Rare Metals2006，25，z1： | 2 |
| 13 | Development of a gaseous and solid-state hybrid system for stationary hydrogen energy storage显示文摘Hydrogen can serve as a carrier to store renewable energy in large scale.However,hydrogen storage still remains a challenge in the current stage.It is difficult to meet the technical requirements applying the conventional storage of compressed gaseous hydrogen in high-pressure tanks or the solid-state storage of hydrogen in suitable materials.In the present work,a gaseous and solid-state(G-S)hybrid hydrogen storage system with a low working pressure below 5 MPa for a 10 kW hydrogen energy storage experiment platform is developed and validated.A Ti-Mn type hydrogen storage alloy with an effective hydrogen capacity of 1.7 wt%was prepared for the G-S hybrid hydrogen storage system.The G-S hybrid hydrogen storage tank has a high volumetric hydrogen storage density of 40.07 kg H_(2)m^(-3) and stores hydrogen under pressure below5 MPa.It can readily release enough hydrogen at a temperature as low as-15C when the FC system is not fully activated and hot water is not available.The energy storage efficiency of this G-S hybrid hydrogen storage system is calculated to be 86.4%-95.9%when it is combined with an FC system.This work provides a method on how to design a G-S hydrogen storage system based on practical demands and demonstrates that the G-S hybrid hydrogen storage is a promising method for stationary hydrogen storage application. | Haizhen Liu Li Xu Yu Han Xin Chen Peng Sheng Shumao Wang Xiantun Huang Xinhua Wang Chenglin Lu Hui Luo Shixuan He Zhiqiang Lan Jin Guo | 2021 | Green Energy & Environment2021，6，4： | 2 |
| 14 | On the Development of Science and Technology Service Industry of Shenyang City 显示文摘 | Shumao Zhang | 2010 | International Journal of Business and Management2010，5，8： | 1 |
| 15 | Flame-retar- dancy and anti-dripping effects of intumescent flame re- tardant incorporating montmorillonite on poly ( lactic acid)显示文摘 | Li Shumao Yuan Hua Yu Tao | 2009 | Polymers for Advanced Technologies2009，20，12： | 1 |
| 16 | UPLC–QTOF/MS-based screening and identification of the constituents and their metabolites in rat plasma and urine after oral administration of Glechoma longituba extract显示文摘 | Shumao Ni Dawei Qian Jin-ao Duan Jianming Guo Er-xin Shang Yan Shu Caifu Xue | 2010 | Journal of Chromatography B2010，，28： | 1 |
| 17 | Structure and properties of bilayer chitosan-gelatin scaffolds 显示文摘 | Jin Shumao Li Guozhao | 2002 | Biomaterials2002，24，： | 1 |
| 18 | Studies on formation and repair of formaldehyde-damaged DNA by detection of DNA-protein crosslinks and DNA breaks显示文摘 | Liu Chang Zhisong Lu Shumao Ding | 2006 | Front Bioscl2006，11，1： | 1 |
| 19 | Effect of particle size on the performance of rare earth–Mg–Ni-based hydrogen storage alloy electrode显示文摘 | Huiping Yuan Zhiyuan Zou Zhinian Li Jianhua Ye Xiumei Guo Lijun Jiang Shumao Wang Xiaopeng Liu | 2013 | International Journal of Hydrogen Energy2013，，19： | 1 |
| 20 | Asymmetric Synthesis of α-Substituted-γ-butyrolactone Empolying Prolinol Type of Auxiliaries显示文摘Eleven (S)-(-)-bishydrocarbyl-(1-alkanoylpyrrolidin-2-yl)-methanol derivatives of three types were synthesized from L-proline, asymmtrically selective alkylation products were obtained by LDA treatment and alkylation using methyl 2-bromoethyl ether, and three types of chiral α-substituted-γ-butyrolactones were obtained by hydrolyzing the alkylation products, with %e.e. being up to 89 percent. | JiaChengNING ShuMAO YeDiGUAN | 2005 | Chinese Chemical Letters2005，16，1： | 1 |
您所在的机构暂未开通此部分的功能，请联系管理员