|
|
|
题名
|
作者
|
年代
|
出处
|
被引量
|
| 1 | Oscillation of Surface PM2.5 Concentration Resulting from an Alternation of Easterly and Southerly Winds in Beijing: Mechanisms and Implications显示文摘We used simultaneous measurements of surface PM_(2.5) concentration and vertical profiles of aerosol concentration,temperature, and humidity, together with regional air quality model simulations, to study an episode of aerosol pollution in Beijing from 15 to 19 November 2016. The potential effects of easterly and southerly winds on the surface concentrations and vertical profiles of the PM_(2.5) pollution were investigated. Favorable easterly winds produced strong upward motion and were able to transport the PM_(2.5) pollution at the surface to the upper levels of the atmosphere. The amount of surface PM_(2.5) pollution transported by the easterly winds was determined by the strength and height of the upward motion produced by the easterly winds and the initial height of the upward wind. A greater amount of PM_(2.5) pollution was transported to upper levels of the atmosphere by upward winds with a lower initial height. The pollutants were diluted by easterly winds from clean ocean air masses. The inversion layer was destroyed by the easterly winds and the surface pollutants and warm air masses were then lifted to the upper levels of the atmosphere, where they re-established a multi-layer inversion. This region of inversion was strengthened by the southerly winds, increasing the severity of pollution. A vortex was produced by southerly winds that led to the convergence of air along the Taihang Mountains. Pollutants were transported from southern–central Hebei Province to Beijing in the boundary layer. Warm advection associated with the southerly winds intensified the inversion produced by the easterly winds and a more stable boundary layer was formed. The layer with high PM_(2.5) concentration became dee-per with persistent southerly winds of a certain depth. The polluted air masses then rose over the northern Taihang Mountains to the northern mountainous regions of Hebei Province. | Zhaobin SUN Xiaoling ZHANG Xiujuan ZHAO Xiangao XIA Shiguang MIAO Ziming LI Zhigang CHENG Wei WEN Yixi TANG | 2018 | Journal of Meteorological Research2018，32，2： | 3 |
| 2 | Analysis on the Impacts of Straw Burning on Air Quality in Beijing -Tianjing - Hebei Region显示文摘The beginning of October is the high occurrence period of straw burning in North China and Jianghuai region. Heavy pollution weather caused by straw burning often takes place in recent two years,and thus human factor increases the unpredictability of the air quality forecast. In the early autumn of 2015,a continuous fog-haze weather and heavy air pollution event occurred in North China and Jianghuai region due to the straw burning. In this paper,the effect of straw burning on air quality under the same adverse diffusive meteorological conditions has been analyzed by using the ground and upper air meteorological observation data and air quality monitoring data of Environmental Protection Agency in recent two years. The comparison results show that the basic conditions of heavy pollution are weak wind and the unfavorable diffusion situation. In contrast,relative humidity is the key factor,only 40% of relative humidity during the straw burning can reach heavy pollution level during no straw burning. | Ma Xiaohui Tang Yixi Sun Zhaobin Li Ziming | 2017 | Meteorological and Environmental Research2017，8，5： | 2 |
| 3 | 3D printing of personalized polylactic acid scaffold laden with GelMA/autologous auricle cartilage to promote ear reconstruction显示文摘At present,the clinical reconstruction of the auricle usually adopts the strategy of taking autologous costal cartilage.This method has great trauma to patients,poor plasticity and inaccurate shaping.Three-dimensional(3D)printing technology has made a great breakthrough in the clinical application of orthopedic implants.This study explored the combination of 3D printing and tissue engineering to precisely reconstruct the auricle.First,a polylactic acid(PLA)polymer scaffold with a precisely customized patient appearance was fabricated,and then auricle cartilage fragments were loaded into the 3D-printed porous PLA scaffold to promote auricle reconstruction.In vitro,gelatin methacrylamide(GelMA)hydrogels loaded with different sizes of rabbit ear cartilage fragments were studied to assess the regenerative activity of various autologous cartilage fragments.In vivo,rat ear cartilage fragments were placed in an accurately designed porous PLA polymer ear scaffold to promote auricle reconstruction.The results indicated that the chondrocytes in the cartilage fragments could maintain the morphological phenotype in vitro.After three months of implantation observation,it was conducive to promoting the subsequent regeneration of cartilage in vivo.The autologous cartilage fragments combined with 3D printing technology show promising potential in auricle reconstruction. | Xingyu Gui Zhiyu Peng Ping Song Li Chen Xiujuan Xu Hairui Li Pei Tang Yixi Wang Zixuan Su Qingquan Kong Zhenyu Zhang Zhengyong Li Ying Cen Changchun Zhou Yujiang Fan Xingdong Zhang | 2023 | Bio-Design and Manufacturing2023，6，4： | 0 |
您所在的机构暂未开通此部分的功能，请联系管理员