|
|
|
题名
|
作者
|
年代
|
出处
|
被引量
|
| 1 | Study of Cracking Mechanism and Wear Resistance in Laser Cladding Coating of Ni-based Alloy显示文摘Nickel-based alloy coatings were widely used for the remanufacturing of dies and moulds by laser cladding,but the crack sensitivity would be increase due to the higher strength and hardness,which reduced the wear resistance of Ni-based alloys.In this paper,Ni-based coatings with the addition of a plastic phase(an austenitic stainless net)were prepared using laser cladding technology,and the CeO_(2)was added in cladding layers.The cracking mechanism,microhardness,microstructure,phase composition,and wear properties were investigated.The relationship between thermal stress and the elastic and plastic fracture had been developed from the standpoint of fracture mechan-ics and thermal elastic fracture mechanics.The fracture criterion of the nickel-based coating was obtained,and the study has shown that the crack sensitivity could be reduced by decreasing the thermal expansion coefficientΔα.Thus,a new method was proposed,which the stainless steel nets were prefabricated on the substrate.It was found that the number of cracks reduced significantly with the addition of stainless steel net.When the stainless steel net with 14 mesh was added in Ni-based coatings,the average microhardness of nickel composite coating was 565 HV_(0.2),which was 2.6 times higher than that of the 45 steel substrate.Although the rare earth oxide 4 wt.%CeO_(2)and stainless steel net were added in the Ni-based coating reducing the microhardness(the average microhardness is 425 HV_(0.2)),the wear resistance of it improved substantially.The wear volume of Ni-based composite coating was 0.56×10^(−5) mm^(3)·N^(−1)·m^(−1),which was 85.1%lower than that of 45 steel.The experiment results have shown that the Nickel-based composite coating is equipped with low crack sensitivity and high abrasive resistance with austenitic stainless net and the rare earth oxide 4 wt.%CeO2.This research offers an efficient solution to produce components with low crack susceptibility and high wear-resistance coatings fabricated by laser cladding. | Zhenglei Yu Lunxiang Li Deqiang Zhang Guangfeng Shi Guang Yang Zezhou Xu Zhihui Zhang | 2021 | Chinese Journal of Mechanical Engineering2021，34，5： | 2 |
| 2 | Pomelo Peel-Inspired 3D-Printed Porous Structure for Efficient Absorption of Compressive Strain Energy显示文摘The porous structure in pomelo peel is believed to be responsible for the protection of its fruit from damage during the free falling from a tree.The quantitative understanding of the relationship between the deformation behavior and the porous structure could pave the way for the design of porous structures for efficient energy absorption.Here,a universal feature of pore distribution in pomelo peels along the radial direction is extracted from three varieties of pomelos,which shows strong correlation to the deformation behavior of the peels under compression.Guided by the porous design found in pomelo peels,porous polyether-ether-ketone(PEEK)cube is additively manufactured and possesses the highest ability to absorb energy during compression as compared to the non-pomelo-inspired geometries,which is further confirmed by the finite element simulation.The nature-optimized porous structure revealed here could guide the design of lightweight and high-energy-dissipating materials/devices. | Baisong Yang Wenhui Chen Renlong Xin Xiaohong Zhou Di Tan Chuan Ding You Wu Liang Yin Chuyang Chen Shan Wang Zhenglei Yu Jonathan TPham Sheng Liu Yifeng Lei Longjian Xue | 2022 | Journal of Bionic Engineering2022，19，2： | 1 |
| 3 | Impinging Cooling with a Crescent Surface Inspired by Barchan Dunes in a Simplified Gas Turbine Transition Section显示文摘For the enhancement of heat transfer efficiency,a novel turbulator inspired by the morphology of barchan dunes,called the mimetic barchan dune(MBD)turbulator,is designed and evaluated in the simplified gas turbine transition section.By using computational fluid dynamics(CFD),the numerical simulations for comparison have been carried out,concluding the smooth thermal surface,a thermal surface with riblet-shaped turbulator and a thermal surface with MBD turbulator.Then,two indicators are investigated for evaluating the coolant performance which are the heat transfer efficiency(η)on the outlet and the pressure loss(ΔP)in the coolant chamber.The numerical results show that the coolant has the best heat transfer efficiency with less pressure loss in the coolant chamber with the MBD turbulator.Then,the effect of the MBD turbulator sizes on heat transfer efficiency is investigated.When the height of the MBD turbulator(h)is set at 8 mm,the maximum amount of heat that could be transfered by the coolant is up to566.2 K and the corresponding heat transfer efficiency is 26.62%.The detail flows have been shown to elucidate the function of the MBD surface which may greatly arouse more design for solving harsh circumstance. | GUO Haotian XU Tao LIANG Xiao YU Zhenglei XING Genyuan GUO Huan | 2019 | Transactions of Nanjing University of Aeronautics and Astronautics2019，36，5： | 1 |
| 4 | Investigation on the Mechanical Properties and Shape Memory Effect of Landing Buffer Structure Based on NiTi Alloy Printing显示文摘With the deepening of human research on deep space exploration,our research on the soft landing methods of landers has gradually deepened.Adding a buffer and energy-absorbing structure to the leg structure of the lander has become an effective design solution.Based on the energy-absorbing structure of the leg of the interstellar lander,this paper studies the appearance characteristics of the predatory feet of the Odontodactylus scyllarus.The predatory feet of the Odontodactylus scyllarus can not only hit the prey highly when preying,but also can easily withstand the huge counter-impact force.The predatory feet structure of the Odontodactylus scyllarus,like a symmetrical cone,shows excellent rigidity and energy absorption capacity.Inspired by this discovery,we used SLM technology to design and manufacture two nickel-titanium samples,which respectively show high elasticity,shape memory,and get better energy absorption capacity.This research provides an effective way to design and manufacture high-mechanical energy-absorbing buffer structures using bionic 3D printing technology and nickel-titanium alloys. | Zhenglei Yu Renlong Xin Zezhou Xu Yining Zhu Xiaolong Zhang Shijie Hao Zhihui Zhang Ping Liang | 2023 | Chinese Journal of Mechanical Engineering2023，36，4： | 0 |
| 5 | Study on Functional Mechanical Performance of Honeycomb Array Structures Inspired by Gideon Beetle显示文摘To obtain bio-inspired structures with superior biological function,four bio-inspired structures named regular arrangement honeycomb structure(RAHS),staggered arrangement honeycomb structure(SAHS),floral arrangement honeycomb structure(FLAHS)and functional arrangement honeycomb structure(FUAHS)are designed by observing the microstructure of the Gideon beetle,based on the optimal size bio-inspired cells by response surface method(RSM)and particle swarm optimization(PSO)algorithm.According to Euler theory and buckling failure theory,compression deformation properties of bio-inspired structures are explained.Experiments and simulations further verify the accuracy of theoretical analysis results.The results show that energy absorption of FLAHS is,respectively,increased by 26.95%,22.85%,and 121.45%,compared with RAHS,SAHS,and FUAHS.Elastic modulus of FLAHS is 110.37%,110.37%,and 230.56% of RAHS,SAHS,and FUAHS,respectively.FLAHS perfectly inherits crashworthiness and energy absorption properties of the Gideon beetle,and FLAHS has the most stable force.Similarly,RAHS,SAHS,and FUAHS,respectively,inherit mechanical properties of the Gideon beetle top horn,the Gideon beetle middle horn,and the abdomen of the beetle.This method,designing bio-inspired structures with biological functions,can be introduced into the engineering field requiring the special function. | Ruiyao Liu Guofeng Yao Zezhou Xu Xue Guo Kuiyang Gao Qing Cao Zhenglei Yu Zhihui Zhang Chunyang Han Jiabao Liu | 2022 | Journal of Bionic Engineering2022，19，4： | 0 |
| 6 | Development of wet adhesion of honeybee arolium incorporated polygonal structure with three-phase composite interfaces显示文摘Inspired by the dynamic wet adhesive systems in nature,various artificial adhesive surfaces have been developed but still face different challenges.Crucially,the theoretical mechanics of wet adhesives has never been sufficiently revealed.Here,we develop a novel adhesive mechanism for governing wet adhesion and investigate the biological models of honeybee arolium for reproducing the natural wet adhesive systems.Micro-nano structures of honeybee arolium and arolium-prints were observed by Cryogenic scanning electron microscopy(Cryo-SEM),and the air pockets were found in the contact interface notably.Subsequently,the adhesive models with a three-phase composite interface(including air pockets,liquid secretion,and hexagonal frames of arolium),were formed to analyze the wet adhesion of honeybee arolium.The results of theoretical calculations and experiments indicated an enhanced adhesive mechanism of the honeybee by liquid self-sucking effects and air-embolism effects.Under these effects,normal and shear adhesion can be adjusted by controlling the proportion of liquid secretion and air pockets in the contact zone.Notably,the air-embolism effects contribute to the optimal coupling of smaller normal adhesion with greater shear adhesion,which is beneficial for the high stride frequency of honeybees.These works can provide a fresh perspective on the development of bio-inspired wet adhesive surfaces. | Lulu LIANG Jieliang ZHAO Qun NIU Li YU Xiangbing WU Wenzhong WANG Shaoze YAN Zhenglei YU | 2024 | Friction2024，12，2： | 0 |
| 7 | Adhesion and corrosion resistance of polycaprolactone coating on NiTi alloy surface after alkali heat pretreatment显示文摘Selective laser melting of nickel-titanium alloy(SLM-NiTi)can precisely control the size of the sample molding structure and has attracted extensive attention due to its special superelasticity and shape memory effect.However,the biological inertness and poor corrosion resistance of SLM-NiTi alloy limit their wide application as biomedical implant materials.In this study,polycaprolactone(PCL)coating was prepared on SLM-NiTi alloy by dipping and pulling method,and the effects of alkali heat pretreatment on the morphology,adhesion,corrosion resistance,long-term stability and biomineralisation of the PCL coatings were investigated.The results showed that PCL coating can substan-tially improve the performance of SLM-NiTi alloy,and the PCL coating after alkali heat pretreatment has higher adhesion(increased from 1,747 to 2,498 mN)and lower corrosion current density(reduced by about an order of magnitude compared to PCL coating alone).In addition,the necessary stability,biomineralisation and biocompatibility ability of coatings were also further improved.Therefore,the alkali heat pretreated PCL-coated SLM-NiTi alloy has good application prospects in implants due to its superior properties. | Zhihui Zhang Yanan Yang Yunting Guo Pengwei Sha Zezhou Xu Zhenglei Yu Jiashun Si Zhengao Zhang Jia Guo Yifan Chen | 2022 | Biosurface and Biotribology2022，8，4： | 0 |
| 8 | Compression Behavior and Failure Mechanisms of Bionic Porous NiTi Structures Built via Selective Laser Melting显示文摘Inspired by the crystal microstructure of metals and the bamboo,the bionic porous NiTi structures with the porosities in the range of 75.8%–84.9%were built via selective laser melting(SLM).The compression behavior and the failure mechanisms of the porous NiTi structures were evaluated.It demonstrated an increase in the elastic modulus and ultimate strength when the porosity was decreased,from 3.06 to 7.66 GPa and from 34.1 to 147.6 MPa,respectively.The relationship between the elastic modulus and the porosity obtained by the finite element analysis exhibited similar tendency with the experiment,and agreed well with the Gibson-Ashby model’s prediction.Based on the theoretical model above and the observation of the deformation processing,the plastic deformation behavior and failure mechanisms of the SLMed porous NiTi structures were analyzed. | Xiaolong Zhang Yue Jiang Shupeng Wang Shuo Wang Ziqiang Wang Zhenglei Yu Zhihui Zhang Luquan Ren | 2023 | Acta Metallurgica Sinica(English Letters)2023，36，6： | 0 |
| 9 | Mechanical Characteristics Analysis of 3D-printing Novel Chiral Honeycomb Array Structures Based on Functional Principle and Constitutive Relationship显示文摘Four novel chiral honeycomb structures inspired by the biological arrangement shape are designed.The functional principle is raised to solve the large deformation of bio-inspired structures and the structural constitutive model is proposed to explain the quasi-static mechanical properties of chiral honeycomb array structures and honeycomb structures.Simulation and experiment results verify the accuracy of theoretical analysis results and the errors are all within 15%.In structural mechanical properties,Equidimensional Chiral Honeycomb Array Structure(ECHS)has excellent mechanical properties.Among ECHS,Small-sized Column Chiral Honeycomb Array Structure(SCHCS)has the best properties.The bearing capacity,specific energy absorption,and specific strength of SCHCS are more than twice as much as the others in this paper.The chiral honeycomb array structure has the best mechanical properties at a certain size.In the structural design,the optimal size model should be obtained first in combination with the optimization algorithm for the protection design. | Ruiyao Liu Guofeng Yao Zezhou Xu Xue Guo Jianyong Li Zhenglei Yu Ping Liang Zhihui Zhang Chunyang Han | 2023 | Journal of Bionic Engineering2023，20，5： | 0 |
| 10 | Shock-Resistant and Energy-Absorbing Properties of Bionic NiTi Lattice Structure Manufactured by SLM显示文摘Each specific structure of organisms is the best choice under specific circumstances.The excellent characteristic structures of these organisms have great application potential in the design and multi-functional optimization of energy-absorbing structures such as vehicle collisions,satellite landings,and military equipment.In this paper,using the principle of structural bionics,using the advantages of the honeycomb structure and the light weight and high strength of beetle elytra,four bionic lattice structures are studied:CH,ZPRH,SCH and IBE.Using NiTi shape memory alloy,a unique material as the base material,samples are prepared using selective laser melting(SLM)technology.By comparing the test results of the quasi-static compression test with the results of the numerical simulation,it is found that compared with the other three bionic lattice structures,the SCH structure has the best energy absorption effect in the effective stroke in the test,and the specific energy absorption can reach 6.32 J/g.ZPRH,SCH,and IBE structures not only have good and stable deformation behavior,but also have excellent impact resistance and shape memory properties.The design of these structures provides a reference for the design of anti-shock cushioning structures with self-recovery functions in the future. | Zhenglei Yu Renlong Xin Zezhou Xu Luming Sha Lixin Chen Yining Zhu Ping Liang Zhihui Zhang Zhenze Liu Qing Cao | 2022 | Journal of Bionic Engineering2022，19，6： | 0 |
您所在的机构暂未开通此部分的功能，请联系管理员