|
|
|
题名
|
作者
|
年代
|
出处
|
被引量
|
| 1 | Development of highway constructing technology in the permafrost region on the Qinghai-Tibet plateau显示文摘The Qinghai-Tibet Highway passes through the Qinghai-Tibet plateau hinterland from north to south, from Kunlun Mountain to Tanggula Mountain. The average altitude is above 4500 m and permafrost covers more than 700 km length of area with high elevation and high temperature. The climate of the plateau is capricious and the surroundings along the road are bad, where the mean annual atmosphere temperature is -2 to -7℃ and the oxygen content is inadequate, which is less than 50% of the sea level, while the solar radiation is higher than 3600 kJ/m2. The basic characteristics of the plateau surroundings are the permafrost, coldness with litter oxygen, and fragile ecosystem. As the air temperature warms all over the world, the permafrost on the plateau responds quickly. The average temperature of permafrost is up by 0.2―0.3℃ in recent 20 years, and the island-permafrost dwindles with a high rate, and the high temperature permafrost degrades quickly, and the temperature of the low temperature permafrost increases remarkably. These gradually cause the highway engineering diseases in the permafrost region. The Qinghai-Tibet highway has experienced much maintenance and rebuilding for 50 years after it was built, and the continual observation and investigation have been made for more than 30 years. This road is the longest test engineering for permafrost research work in China. It is no doubt that it is also the greatest engineering project in plateau permafrost region. The Ministry of Communication in China initiated the research project 'Research on a series of technologies for highway constructing in the permafrost regions' in 2002, which was to meet the challenges from the effect of climatic warming on the permafrost. The project systematically studied the permafrost engineering theories, methods for survey and design, engineering stabilization measures, preventing of the road disasters and maintaining, environment protection and the techniques to prolong the road engineering life in the cold surroundings with high altitude and less oxygen. This article describes a series of technologies for highway constructing according to the special surroundings in the plateau, including some innovative achievements and the research and development of permafrost engineering. | WANG ShuangJie CHEN JianBing ZHANG JinZhao LI ZhuLong | 2009 | Science China(Technological Sciences)2009，52，2： | 16 |
| 2 | The HuangZaoSi Maize Genome Provides Insights into Genomic Variation and Improvement History of Maize显示文摘Maize is a globally important crop that was a classic model plant for genetic studies. Here, we report a 2.2 Gb draft genome sequence of an elite maize line, HuangZaoSi (HZS). Hybrids bred from HZS-improved lines (HILs) are planted in more than 60% of maize fields in China. Proteome clustering of six completed sequeneed maize genomes show that 638 proteins fall into 264 HZS-specific gene families with the majority of contributions from tandem duplication events. Resequencing and comparative analysis of 40 HZSrelated lines reveals the breeding history of HILs. More than 60% of identified selective sweeps were clustered in identity.by.descent conserved regions, and yield-related genes/QTLs were enriched in HZS characteristic selected regions. Furthermore, we dem on strated that HZS-specific family genes were not uniformly distributed in the genome but enriched in improvement/function.related genomic regions. This study provides an important and novel resource for maize genome research and expands our knowledge on the breadth of genomic variation and improvement history of maize. | Chunhui Li Wei Song Yingfeng Luo Shenghan Gao Ruyang Zhang Zi Shi Xiaqing Wang Ronghuan Wang Fengge Wang Jidong Wang Yanxin Zhao Aiguo Su Shuai Wang Xin Li Meijie Luo Shuaishuai Wang Yunxia Zhang Jianrong Ge Xinyu Tan Ye Yuan Xiaochun Bi Hang He Jianbing Yan Yuandong Wang Songnian Hu Jiuran Zhao | 2019 | Molecular Plant2019，12，3： | 15 |
| 3 | ZmCOL3, a CCT gene represses flowering in maize by interfering with the circadian clock and activating expression of ZmCCT显示文摘Flowering time is a trait vital to the adaptation of flowering plants to different environments.Here, we report that CCT domain genes play an important role in flowering in maize(Zea mays L.).Among the 53 CCT family genes we identified in maize, 28 were located in flowering time quantitative trait locus regions and 15 were significantly associated with flowering time, based on candidate-gene association mapping analysis.Furthermore, a CCT gene named ZmCOL3 was shown to be a repressor of flowering.Overexpressing ZmCOL3 delayed flowering time by approximately 4 d, in either long-day or short-day conditions.The absence of one cytosine in the ZmCOL3 3'UTR and the presence of a 551 bp fragment in the promoter region are likely the causal polymorphisms contributing to the maize adaptation from tropical to temperate regions.We propose a modified model of the maize photoperiod pathway, wherein ZmCOL3 acts as an inhibitor of flowering either by transactivating transcription of ZmCCT, one of the key genes regulating maize flowering, or by interfering with the circadian clock. | Minliang Jin Xiangguo Liu Wei Jia Haijun Liu Wenqiang Li Yong Peng Yanfang Du Yuebin Wang Yuejia Yin Xuehai Zhang Qing Liu Min Deng Nan Li Xiyan Cui Dongyun Hao Jianbing Yan | 2018 | Journal of Integrative Plant Biology2018，60，6： | 14 |
| 4 | Distant eQTLs and Non-coding Sequences Play Critical Roles in Regulating Gene Expression and Quantitative Trait Variation in Maize显示文摘 | Haijun Liu Xin Luo Luyao Niu Yingjie Xiao Lu Chen Jie Liu Xiaqing Wang Minliang Jin Wenqiang Li Qinghua Zhang Jianbing Yan | 2017 | Molecular Plant2017，10，3： | 13 |
| 5 | Adsorptive removal of antibiotics from water using magneticion exchange resin显示文摘The occurrence of antibiotics in the environment has recently raised serious concern regarding their potential threat to aquatic ecosystem and human health. In this study, the magnetic ion exchange(MIEX) resin was applied for removing three commonly-used antibiotics, sulfamethoxazole(SMX), tetracycline(TCN) and amoxicillin(AMX) from water.The results of batch experiments show that the maximum adsorption capacities on the MIEX resin for SMX, TCN and AMX were 789.32, 443.18 and 155.15 μg/m L at 25°C,respectively, which were 2–7 times that for the powdered activated carbon. The adsorption kinetics of antibiotics on the MIEX resin could be simulated by the pseudo-second-order model(R^2= 0.99), and the adsorption isotherm data were well described by the Langmuir model(R^2= 0.97). Solution p H exhibited a remarkable impact on the adsorption process and the absorbed concentrations of the tested antibiotics were obtained around the neutral p H.The MIEX resin could be easily regenerated by 2 mol/L Na Cl solution and maintained high adsorption removal for the tested antibiotics after regeneration. Anion exchange mechanism mainly controlled the adsorption of antibiotic and the formation of hydrogen binding between the antibiotic and resin can also result in the increase of adsorption capacity. The high adsorption capacity, fast adsorption rate and prominent reusability make the MIEX resin a potential adsorbent in the application for removing antibiotics from water. | Tianyue Wang Xun Pan Weiwei Ben Jianbing Wang Pin Hou Zhimin Qiang | 2017 | Journal of Environmental Sciences2017，29，2： | 12 |
| 6 | Genotype variations in accumulation of cadmium and lead in celery (Apium graveolens L.) and screening for low Cd and Pb accumulative cultivars显示文摘To help reduce risks of heavy metal pollution, two pot experiments were conducted to investigate the variations, transfer potential, and stability of Cadmium (Cd) and Lead (Pb) accumulations in celery (Apium graveolens L.) and to screen for low Cd and Pb accumulative cultivars. The maximum differences in shoot Cd concentration were 4.7-fold under low-Cd exposure and 3.3-fold under high-Cd exposure. These genotype variations in Cd accumulation are sufficiently large to help reduce Cd contamination risk in soil by using the Low-Cd-Accumulative genotypes. Cd accumulation of the Low-Cd-Accumulative genotypes is significantly positive correlated with Pb accumulation. Evidence obtained proves that Cd and Pb accumulations in celery are stable and genotype-dependent at the cultivar level. The presence of high-Pb contamination in soil promoted Cd accumulation in shoots of celery. Celery is considered a species with high risks in Cd pollution and low risks in Pb pollution. Among the tested cultivars, cv. Shuanggang- kangbing (SGKB) had the lowest shoot Cd and Pb accumulating abilities, and thus is the most important material for breeding of pollution-safe cultivars (PSCs) to minimize Cd and Pb accumulations in celery. | Kun ZHANG Jianbing WANG Zhongyi YANG Guorong XIN Jiangang YUAN Junliang XIN Charlie HUANG | 2013 | Frontiers of Environmental Science & Engineering2013，7，1： | 9 |
| 7 | Investigation on the spatial distribution characteristics of behind-armor debris formed by the perforation of EFP through steel target显示文摘The behind-armor debris(BAD) formed by the perforation of an EFP is the main damage factor for the secondary destruction to the behind-armor components.Aiming at investigating the BAD caused by EFP,flash X-ray radiography combined with an experimental witness plate test method was used,and the FEM-SPH adaptive conversion algorithm in LS-DYNA software was erployed to model the perforation process.The simulation results of the debris cloud shape and number of debris were in good agreement with the flash X-ray radiographs and perforated holes on the witness plate,respectlvely.Threedimensional numerical simulations of EFP's penetration under various impact conditions were conducted.The results show that,an ellipsoidal debris cloud,with the major-to-minor axis radio(a/b)smaller than that caused by shaped charge jets,was formed behind the target.With the increase of target thickness(h) and decrease of impact velocity(v_0) and obliquity(θ),the value of a/b decreases.The number of debris ejected from target is significantly higher than that from EFP.Based on the statistical analysis of the spatial distribution of the BAD,An engineering calculation model was established considering the influence of h,v_0 and θ.The model can with reasonable accuracy predict the quantity and velocity distribution characteristics of BAD formed by EFP. | Xin Wang Jianwei Jiang Shengjie Sun Jianbing Men Shuyou Wang | 2020 | Defence Technology(防务技术)2020，16，1： | 6 |
| 8 | The RppC-AvrRppC NLR-effector interaction mediates the resistance to southern corn rust in maize显示文摘Southern corn rust(SCR),caused by the fungal pathogen Puccinia polysora,is a major threat to maize pro-duction worldwide.Efficient breeding and deployment of resistant hybrids are key to achieving durable control of SCR.Here,we report the molecular cloning and characterization of RppC,which encodes an NLR-type immune receptor and is responsible for a major SCR resistance quantitative trait locus.Further-more,we identified the corresponding avirulence effector,AvrRppC,which is secreted by P.polysora and triggers RppC-mediated resistance.Allelic variation of AvrRppC directly determines the effectiveness of RppC-mediated resistance,indicating that monitoring of AvrRppC variants in the field can guide the rational deployment of RppC-containing hybrids in maize production.Currently,RppC is the most frequently deployed SCR resistance gene in China,and a better understanding of its mode of action is crit-ical for extending its durability. | Ce Deng April Leonard James Cahill Meng Lv Yurong Li Shawn Thatcher Xueying Li Xiaodi Zhao Wenjie Du Zheng Li Huimin Li Victor Llaca Kevin Fengler Lisa Marshall Charlotte Harris Girma Tabor Zhimin Li Zhiqiang Tian Qinghua Yang Yanhui Chen Jihua Tang Xintao Wang Junjie Hao Jianbing Yan Zhibing Lai Xiaohong Fei Weibin Song Jinsheng Lai Xuecai Zhang Guoping Shu Yibo Wang Yuxiao Chang Weiling Zhu Wei Xiong Juan Sun Bailin Li Junqiang Ding | 2022 | Molecular Plant2022，15，5： | 6 |
| 9 | Genomic, Transcriptomic, and Phenomic Variation Reveals the Complex Adaptation of Modern Maize Breeding显示文摘 | Haijun Liu Xiaqing Wang Marilyn L. Warburton Weiwei Wen Minliang Jin Min Deng Jie Liu Hao Tong Qingchun Pan Xiaohong Yang Jianbing Yan | 2015 | Molecular Plant2015，8，6： | 6 |
| 10 | Catalytic wet air oxidation of phenol with functionalized carbon materials as catalysts:Reaction mechanism and pathway显示文摘The development of highly active carbon material catalysts in catalytic wet air oxidation(CWAO)has attracted a great deal of attention. In this study different carbon material catalysts(multi-walled carbon nanotubes,carbon fibers and graphite) were developed to enhance the CWAO of phenol in aqueous solution. The functionalized carbon materials exhibited excellent catalytic activity in the CWAO of phenol. After 60 min reaction,the removal of phenol was nearly100% over the functionalized multi-walled carbon,while it was only 14% over the purified multi-walled carbon under the same reaction conditions. Carboxylic acid groups introduced on the surface of the functionalized carbon materials play an important role in the catalytic activity in CWAO. They can promote the production of free radicals,which act as strong oxidants in CWAO. Based on the analysis of the intermediates produced in the CWAO reactions,a new reaction pathway for the CWAO of phenol was proposed in this study. There are some differences between the proposed reaction pathway and that reported in the literature. First,maleic acid is transformed directly into malonic acid. Second,acetic acid is oxidized into an unknown intermediate,which is then oxidized into CO2 and H2O. Finally,formic acid and oxalic acid can mutually interconvert when conditions are favorable. | Jianbing Wang Wantao Fu Xuwen He Shaoxia Yang Wanpeng Zhu | 2014 | Journal of Environmental Sciences2014，26，8： | 6 |
| 11 | Treatment of coking wastewater using oxic-anoxic-oxic process followed by coagulation and ozonation显示文摘An oxic-anoxic-oxic(O-A-O)system followed by coagulation and ozonation processes was used to study the treatment of coking wastewater.In the O-A-O process,the removals of NH4+-N,total nitrogen and COD were 91.5-93.3%,91.3-92.6%and 89.1-93.8%,respectively when employing hydraulic residence times of 60 h for the biochemical system.High removal of NH4+-N was obtained due to the placement of an aerobic tank in front of A-O system which can mitigate the inhibitory effect of toxic compounds in coking wastewater on nitrifying bacteria.Addition of methanol into the anoxic reactor greatly increased the removal of total nitrogen,indicating that denitrifiers can hardly use organic compounds in coking wastewater as carbon source for denitrification.COD values of the effluent from the O-A-O system were still higher than 260 mg/L even with a prolonged time of 160 h mainly due to the high refractory properties of residual compounds in the effluent.The subsequent coagulation and ozonation processes resulted in the COD removal of 91.5%-93.3%and reduced the relative abundance of large molecular weight(MW)organics(>1 kDa)from 55.8%to 20.93%with the ozone,PAC and PAM dosages of 100,150 and 4 mg/L respectively.Under these conditions,the COD value and concentration of polycyclic aromatic hydrocarbons in the final effluent were less than 80 and 0.05 mg/L,respectively,which meet the requirement of the Chinese emission standard.These results indicate that the combined technology of O-A-O process,coagulation and ozonation is a reliable way for the treatment of coking wastewater. | Jianbing Wang Yuxian Ji Fengyuan Zhang Dongliang Wang Xuwen He Chunrong Wang | 2019 | Carbon Resources Conversion2019，2，2： | 5 |
| 12 | Revisiting Al-Ni-Zr bulk metallic glasses using the 'cluster-resonance' model显示文摘Six series of alloys,namely,Ni3Zr6Alx,Ni3Zr7Alx,Ni4Zr9Alx,Ni3Zr8Alx,Ni3Zr9Alx and Ni3Zr10Alx (x=1,1.5,2,3) were designed in this work and the bulk metallic glass (BMG) formation of these compositions was investigated by copper mold suction casting. A centimeter-scale BMG sample was obtained for the Ni4Zr9Al2 (Al13.3Ni26.7Zr60 in atomic percent) composition. The thermal glass parameters for this BMG were determined to be ΔTx = 68 K,Trg = 0.579,and γm = 0.689. Using the 'cluster-resonance' model for glass formation an optimal BMG composition was determined using the cluster formula [Ni3Zr9](Al2Ni1). | LI FengWei QIANG JianBing WANG YingMin WANG Qing DONG XingLong DONG Chuang | 2011 | Chinese Science Bulletin2011，56，36： | 5 |
| 13 | Large-Scale Discovery of Non-conventional Peptides in Maize and Arabidopsis through an Integrated Peptidogenomic Pipeline显示文摘Non-conventional peptides(NCPs),which include small open reading frame-encoded peptides,play critical roles in fundamental biological processes.In this study,we developed an integrated peptidogenomic pipeline using high-throughput mass spectra to probe a customized six-frame translation database and applied it to large-scale identification of NCPs in plants.A total of 1993 and 1860 NCPs were unambiguously identified in maize and Arabidopsis,respectively.These NCPs showed distinct characteristics compared with conventional peptides and were derived from introns,3′UTRs,5′UTRs,junctions,and intergenic regions.Furthermore,our results showed that translation events in unannotated transcripts occur more broadly than previously thought.In addition,we found that dozens of maize NCPs are enriched within regions associated with phenotypic variations and domestication selection,indicating that they potentially are involved in genetic regulation of complex traits and domestication in maize.Taken together,our study developed an integrated peptidogenomic pipeline for large-scale identification of NCPs in plants,which would facilitate global characterization of NCPs from other plants.The identification of large-scale NCPs in both monocot(maize)and dicot(Arabidopsis)plants indicates that a large portion of plant genome can be translated into biologically functional molecules,which has important implications for functional genomic studies. | Shunxi Wang Lei Tian Haijun Liu Xiang Li Jinghua Zhang Xueyan Chen Xingmeng Jia Xu Zheng Shubiao Wu Yanhui Chen Jianbing Yan Liuji Wu | 2020 | Molecular Plant2020，13，7： | 4 |
| 14 | Three-Gorge Dam influences wetland macrophytes in middle and lower reaches of Yangtze显示文摘Dongting Lake,located in the middle and lower reaches of Yangtze,is regarded as a lake during the water swelling period and a continent in the ebbing period.The construction of the Three-Gorge Dam has influenced the water level of Dongting Lake and the growth of wetland macrophytes in the area.In this study,the growth of main species of wetland macrophytes,such as Carex and Phragmites at Dongting Lake,was observed,and the hydraulic gradient,one of the main factors dominating the abundance and distribution of wetland macrophytes,was also studied at six stations in Dongting Lake area and the effect of the Three-Gorge Dam construction on the growth of wetland macrophytes was observed. | Wang Lingling Zeng Guangming Li Zhongwu Su Xiaokang Li Jianbing Huang Guohe | 2007 | Progress in Natural Science:Materials International2007，17，9： | 4 |
| 15 | Hydrodynamic cavitation as an efficient method for the formation of sub-100 nm O/W emulsions with high stability显示文摘Hydrodynamic cavitation,a newly developed process intensification technique,has demonstrated immense potential for intensifying diverse physical and chemical processes.In this study,hydrodynamic cavitation was explored as an efficient method for the formation of sub-100 nm oil-in-water(O/W) emulsions with high stability.O/W emulsion with an average droplet size of 27 nm was successfully prepared.The average droplet size of O/W emulsions decreased with the increase of the inlet pressure,number of cavitation passes and surfactant concentration.The formed emulsion exhibited admirable physical stability during 8 months.Moreover,the hydrodynamic cavitation method can be generalized to fabricate large varieties of O/W emulsions,which showed great potential for large-scale formation of O/W emulsions with lower energy consumption. | Zhiliang Zhang Guangquan Wang Yong Nie Jianbing Ji | 2016 | Chinese Journal of Chemical Engineering2016，24，10： | 4 |
| 16 | Geological Factors for the Formation of Xi'an Ground Fractures显示文摘Xi'an ground fractures are the most typical ground fractures in China. Fourteen fractures have nearly divided the historical city into several distinct sections. These fractures are parallel and distributed in NEE direction at the same interval, with all features exhibiting a down dropping southerly block which extends to connect with the underlying fault. The activities of fractures are primarily expressed as normal faults. The faulted strata are well defined and dislocation displacement increases with depth. Thus, fractures have the characteristics of syn-sedimentary faults, which constitute the hanging wall of the Lintong-Chang'an fault branch system. Crustal thinning caused by the uplifting of upper mantle provides a power source for extension and stretching along the fracture surface of the upper crust, which results in a series of extensional faults and the suitable conditions for forming massive ground fractures. The movement of tectonic blocks influences the normal dip-slipping tension of Lintong-Chang'an fault branches, and produces a series of secondary tectonic fractures adjacent to surface, which constitute the prototype of ground fractures. The recent regional tensile stress produced by modern mainland deformation, also profoundly influences the current activity of Xi'an ground fractures. | Jianbing Peng Wei Qu Jun Ren Qin Zhang Feiyong Wang | 2018 | Journal of Earth Science2018，29，2： | 4 |
| 17 | A universal solution to one-dimensional oscillatory integrals显示文摘How to calculate the highly oscillatory integrals is the bottleneck that restraints the research of light wave and electromagnetic wave's propagation and scattering. Levin method is a classical quadrature method for this type of integrals. Unfortunately it is susceptible to the system of linear equations' ill-conditioned behavior. We bring forward a universal quadrature method in this paper,which adopts Chebyshev differ-ential matrix to solve the ordinary differential equation (ODE). This method can not only obtain the indefinite integral' function values directly,but also make the system of linear equations well-conditioned for general oscillatory integrals. Furthermore,even if the system of linear equations in our method is ill-conditioned,TSVD method can be adopted to solve them properly and eventually obtain accurate integral re-sults,thus making a breakthrough in Levin method's susceptivity to the system of linear equations'ill-conditioned behavior. | LI JianBing WANG XueSong WANG Tao | 2008 | Science in China(Series F)2008，51，10： | 4 |
| 18 | Composition design of superhigh strength maraging stainless steels using a cluster model显示文摘The composition characteristics of maraging stainless steels were studied in the present work investigation using a cluster-plus-glue-atom model. The least solubility limit of high-temperature austenite to form martensite in basic Fe–Ni–Cr corresponds to the cluster formula [NiFe12]Cr3,where NiFe12is a cuboctahedron centered by Ni and surrounded by 12 Fe atoms in FCC structure and Cr serves as glue atoms. A cluster formula [NiFe12](Cr2Ni) with surplus Ni was then determined to ensure the second phase(Ni3M) precipitation,based on which new multicomponent alloys [(Ni,Cu)16Fe192](Cr32(Ni,Mo,Ti,Nb,Al,V)16) were designed. These alloys were prepared by copper mould suction casting method,then solid-solution treated at 1273 K for 1 h followed by water-quenching,and finally aged at 783 K for 3 h. The experimental results showed that the multi-element alloying results in Ni3M precipitation on the martensite,which enhances the strengths of alloys sharply after ageing treatment. Among them,the aged [(Cu4Ni12)Fe192](Cr32(Ni8.5Mo2Ti2Nb0.5Al1V1)) alloy(Fe74.91Ni8.82Cr11.62Mo1.34Ti0.67Nb0.32Al0.19V0.36Cu1.78wt%) has higher tensile strengths with YS?1456 MPa and UTS?1494 MPa. It also exhibits good corrosion-resistance in 3.5 wt% NaCl solution. | Zhen Li Ruiqian Zhang Qianfeng Zha Yingmin Wang Jianbing Qiang Chuang Dong | 2014 | Progress in Natural Science:Materials International2014，24，1： | 4 |
| 19 | Study on the technology for highway construction and engineering practices in permafrost regions显示文摘In order to systemically summarize and integrate technology of highway construction in permafrost regions on the Qinghai-Tibet Plateau,we studied disciplines and mechanisms of formation and development of problems and challenges in highway engineer-ing in high-altitude permafrost regions based on construction experiences for 50 years and on 30 years of research regarding the Qinghai-Tibet and Xikang highways.Embankments,pavements,bridges,and countermeasures for ecosystem protection in per-mafrost regions were the main study objects.We combined extensive analysis of key problems of engineering stability with inter-action between permafrost and highways,theoretical models,indoor tests,and field tests to reveal the interaction between em-bankments,pavements,bridge piles,and permafrost.In this paper,we propose a series of engineering measures for highway sta-bility,design parameters,key indexes for pavement durability in low temperature,relationships between re-freezing time of bridge-pile foundation and strength development as well as ecosystem recovery in high-latitude cold regions;these eventually form a construction technology package for permafrost regions. | ShuangJie Wang JianBing Chen JiLin Qi | 2009 | Research in Cold and Arid Regions2009，1，5： | 3 |
| 20 | Multifunctional nucleic acid nanostructures for gene therapies显示文摘 | Jianbing Liu Zhengang Wang Shuai Zhao Baoquan Ding | 2018 | Nano Research2018，11，10： | 3 |
您所在的机构暂未开通此部分的功能，请联系管理员